S+S Regeltechnik Rymaskon 200-Modbus Series, Руководство пользователя

Страница: 35 / 55

RYM ASKON
®
200-Modbus
Modbus Slave User Manual
© S+S REGELTECHNIK GMBH
| THURN-UND-TAXIS-STR.22 | 90411 NÜRNBERG | GERMANY | FON +49(0)911 519470 | www.SplusS.de
Page 35 of 55
Register Name
Register
Address
Bit Position
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
config_display_
value_13
282
0x011A
unit_modbus
[0x0]
unit
[0x0]
CAL
[0]
semantic_meaning
[0x00]
283
0x011B
VSA
[0]
VEU
[0]
DSSA
[0]
DSEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
config_display_
value_14
284
0x011C
unit_modbus
[0x0]
unit
[0x0]
CAL
[0]
semantic_meaning
[0x00]
285
0x011D
VSA
[0]
VEU
[0]
DSSA
[0]
DSEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
config_display_
value_15
286
0x011E
unit_modbus
[0x0]
unit
[0x0]
CAL
[0]
semantic_meaning
[0x00]
287
0x011F
VSA
[0]
VEU
[0]
DSSA
[0]
DSEU
[0]
[0]
[0] [0]
[0] [0] [0]
[0]
[0] [0] [0] [0] [0]
These registers hold the configuration of the 16 display values.
!!! For both, unit and unit_modbus the following values are possible:
0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC
no
unit
°C °F cfm l/s m³/h Pa inWC V % %RH ppm °F dec.
Bits 0-11 of the higher address of each configuration register indicate the symbols that are displayed along
with the corresponding display value.
These two bits define if the value displayed is taken from a display_value register at address 64 to 79 (see
Table 11 on Page 22) or from a sensor_value register at address 48 to 56 (see Table 10 on Page 21).
The following states are valid:
0 – defines that the value is taken from a display_value register that has to be set via modbus.
1 – defines that the value is taken from a sensor_value (+ offset_value) register that is automatically
updated with the current sensor value.
VEU: Visible for End User
VSA: Visible for System Administrator
These two bits define if the display value is visible for the end user and/or the system administrator.
If set to ‘1’ the value will be visible.
!!! See
Table 30
on Page 40 for example configurations of display values or set points.
semantic_meaning:
is used to provide information about the semantic meaning and the source of
the value. For further information please see Table 29 on Page 38.
CAL:
if set to ‘1’ the corresponding offset_value can be edited in
CALIBRATION-mode (only capable if DSEU or DSSA is set to ‘1’)
unit:
defines a unit with which the corresponding display value appears on the
LCD
unit_modbus:
defines a unit that the corresponding display value register appeare on
Modbus
DSEU: Display Source for End User
DSSA: Diplay Source for System Administrator
Table 27: Display Value Configuration