S.R.Smith River Run Slide 19A Скачать руководство пользователя страница 18

Страница: 18 / 20

I N S TA L L AT I O N I N S T R U C T I O N S

R I V E R R U N S L I D E

SBK-RR INSTALL | 0419

srsmith.com

I N S T A L L A T I O N I N S T R U C T I O N S

R I V E R R U N S L I D E

RIVER RUN FLUME & ANCHOR SUPPORT HARDWARE

The entry frame support anchor comes with a part specific hardware kit. Use hardware set BYOS2-101-SS.

The 20˚ support anchors all attach to flume sections using the hardware kit BYOS2-102-SS.

ADDITIONAL ANTI-SEIZE NOTICE:

S.R.Smith adds additional anti-seize packets to BYOS1 & BYOS2 shipments, as follows:

1–5 sections: 1 packet, included in the BYOS-101-COMBO or BYOS2-101-SS kit.
6–10 sections: +1 packet, added to last section before exit*.

River Run exits do not have hardware.

BYOS2-102-SS – FLUME TO FLUME SS HARDWARE KIT

QTY

PART NUMBER

COMPONENT DESCRIPTION

H-SS 3/8X1-34

3/8”-16X1-3/4” Hex Bolt Stainless Steel

H-SS 3/8 FLT WA

3/8” MS 815 Flat Washer Stainless Steel

H-SS 3/8 LOC WA

3/8” Lock Washer Stainless Steel

H-SS 3/8 F NUT

3/8”-16 Hex Nut Stainless Steel

HARDWARE NOTE:

Use a small dab of anti-seize

lubricant (included) on all

bolt threads.

FIG. 25 (BYOS2-101-SS)

Entry Section/Handrails SS Hardware Kit

FIG. 26 (BYOS2-102-SS)

Flume to Flume SS Hardware Kit

BYOS2-101-SS – ENTRY SECTION/HANDRAILS SS HARDWARE KIT

QTY

PART NUMBER

COMPONENT DESCRIPTION

H-SS 3/8X1 HB

3/8”-16X1” Hex Bolt Stainless Steel

H-SS 3/8 FLT WA

3/8” MS 815 Flat Washer Stainless Steel

H-SS 3/8 LOC WA

3/8” Lock Washer Stainless Steel

H-SS 3/8 F NUT

3/8” Hex Nut Stainless Steel

H-ANTI-SEIZE

Single Use Anti-Seize Packet

Содержание River Run Slide 19A




















Результаты поиска

Содержание River Run Slide 19A

Отзывы:

S.R.Smith River Run Slide 19A, Инструкции по сборке/установке, Страница: 18 / 20

Результаты поиска

Содержание River Run Slide 19A

Отзывы: