background image

  I N S TA L L AT I O N   I N S T R U C T I O N S  

R I V E R   R U N   S L I D E

3

SBK-RR INSTALL  |  0419

Copyright ® 2019 S.R.Smith, LLC All rights reserved. | 

srsmith.com

1. 

Everyone who uses this slide must know, understand and follow these instructions

2. 

The ANSI/APSP/ICC-5 2011 standard for above ground pools prohibits the use of slides or diving boards on above ground pools.

3. 

This slide should never be installed on above ground pools, ponds, floating docks or platforms, boat docks or houseboats or any 
natural body of water.

4. 

Be familiar with the shape and depth of the pool before you slide. This slide should only be used with the proper water safety 
envelope, as described in Diagrams A, B & C on page 3 and in accordance with the slide positioning diagrams on page 4.

5. 

Because the slide may only be used in water 4.5’ deep or greater, all slide users must be able to swim in deep water.

6. 

Weight limit for this slide is 350 pounds, no slider weighing more than 350 pounds may use this slide.

7. 

The surface of the slide is very slippery when wet; USE CAUTION when entering the slide and when transitioning from  
standing to sitting.

8. 

Slide in a feet first sitting position ONLY.

9. IMPORTANT: 

sliding headfirst is prohibited: serious spinal injury resulting in paralysis or death can result.

10.  Maintain adult supervision at all times.
11.  Only one person at a time is allowed on the slide.
12.  Be sure the water delivery system is on and lubricating the slide prior to use.
13.  Collision with another swimmer or a diver can result in serious injury or death for one or both persons: Before sliding, always 

make sure that the path in front of the slide is free from any (including submerged) obstructions including other people or 
objects in the pool such as rafts, inner tubes etc. When a diving board is also present, make sure you do not use the slide while 
someone is on or using a diving board. Take turns.

14.  No roughhousing or horseplay should be allowed on the slide at any time.
15.  Do not stand, jump or dive from any part of the slide.
16.  Do not slide on objects such as rafts or inner tubes. doing so greatly increases your risk of injury.
17.  Do not slide through or at objects such as rafts or inner tubes, doing so greatly increases your risk of injury.
18.  Do not use this slide if physically impaired or handicapped without your doctor’s permission.
19.  Do not use this slide with a history of heart conditions, seizures, back problems, fainting or fear of heights.
20. Do 

NOT use this slide if you are pregnant.

21.  Do not drink alcohol and use this slide.
22.  Don’t take chances, inspect the slide at least once a year (see the slide inspection list on page 16, do not use the slide if any part 

becomes loose, damaged, weakened or broken. If necessary, before using the slide again, have it inspected and repaired by a 
competent professional familiar with pool slides.

INTENDED USE 

INSTRUCTIONS

WARNING

WARNING: SERIOUS INJURY OR DEATH CAN RESULT FROM THE  

IMPROPER INSTALLATION OR USE OF THIS SLIDE.

SLIDE IN A SITTING 

POSITION ONLY

Face forward on the slide, holding the legs and arms with the 

palms of your hands forward and tilted up.

DO NOT SLIDE HEAD FIRST

SERIOUS INJURY 

CAN RESULT

DEEP WATER 

SWIMMERS 

ONLY

Содержание River Run Slide 19A





















Отзывы: