S.R.Smith River Run Slide 19A страница 2 Скачать руководство пользователя

Страница: 2 / 20

WARNING:

IMPORTANT INSTALLATION

INFORMATION

The installation of this product should be done only by a licensed and professional installer.

Installation should be done strictly in conformance with all local building codes, electrical

codes and other building and safety laws and regulations. Among other things, that your

installer should carefully analyze the need to bond the product to prevent an electrical

hazard. Failure to properly install this product could result in a dangerous condition, including

but not limited to electrical and or structural hazards. S.R.Smith. disclaims all liability arising

from the installation and the user assumes all risk associated with the installation.

For Technical Support or Assistance, Contact Customer Service at:

Canby, Oregon | 800.824.4387

Tucson, Arizona | 800.737.5386

srsmith.com

For warranty information:

srsmith.com/warranty

To obtain complete copies of the ANSI/APSP/ICC-5 2011 Standard for Residential

In-ground Pools or to obtain copies of the “Plan Your Dive, Steer Up” or

“The Sensible Way to Enjoy Your In-ground Swimming Pool” contact:

The Association of Pool & Spa Professionals (APSP)

2111 Eisenhower Ave.

Alexandria, VA 22314

(703) 838-0083

www.theapsp.org

WARNING

Содержание River Run Slide 19A




















Результаты поиска

Содержание River Run Slide 19A

Отзывы:

Похожие инструкции для River Run Slide 19A

Бренды по названию

Популярные бренды

S.R.Smith River Run Slide 19A, Инструкции по сборке/установке

Результаты поиска

Содержание River Run Slide 19A

Отзывы:

Похожие инструкции для River Run Slide 19A

Бренды по названию

Популярные бренды