4 − English
MITER SAW SPECIFIC SAFETY RULES
Do not use another person as a substitute for a table
extension or as additional support.
Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling
you and the helper into the spinning blade.
The cut-off piece must not be jammed or pressed by
any means against the spinning saw blade.
If confined,
i.e. using length stops, the cut-off piece could get wedged
against the blade and thrown violently.
Always use a clamp or a fixture designed to properly
support round material such as rods or tubing.
Rods
have a tendency to roll while being cut, causing the blade
to bite and pull the work with your hand into the blade.
Let the blade reach full speed before contacting the
workpiece.
This will reduce the risk of the workpiece
being thrown.
If the workpiece or blade becomes jammed, turn
the miter saw off. Wait for all moving parts to stop
and disconnect the plug from the power source and/
or remove the battery pack. Then work to free the
jammed material.
Continued sawing with a jammed
workpiece could cause loss of control or damage to the
miter saw.
After finishing the cut, release the switch, hold the
saw head down and wait for the blade to stop before
removing the cut-off piece.
Reaching with your hand
near the coasting blade is dangerous.
Hold the handle firmly when making an incomplete cut
or when releasing the switch before the saw head is
completely in the down position.
The braking action of
the saw may to be suddenly pulled downward, causing
a risk of injury.
Save these instructions.
Refer to them frequently and
use to instruct other users. If you loan someone this tool,
loan them these instructions also.
ADDITIONAL SAFETY RULES
Use the proper extension cord.
Make sure your extension
cord is in good condition. Use only a cord heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. A wire gauge size (A.W.G.) of at
least
14
is recommended for an extension cord 25 feet
or less in length. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Inspect tool cords periodically.
If damaged, have
repaired by a qualified service technician at an authorized
service facility. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
Inspect extension cords periodically
and replace if
damaged.
Polarized plugs.
To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
Know your power tool.
Read the operator’s manual
carefully. Learn the applications and limitations as well
as the specific potential hazards related to this tool.
Always wear eye protection with side shields which
is marked to comply with ansi Z87.1 when using this
product.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible serious injury.
Never stand on tool.
Serious injury could occur if the tool
is tipped or if the cutting tool is unintentionally contacted.
Keep guards in place
and in good working order.
Use the right direction of feed.
Feed work into a blade,
cutter, or sanding spindle against the direction of rotation
of the blade, cutter, or sanding spindle only.
Never leave tool running unattended. Turn the power
off.
Don’t leave tool until it comes to a complete stop.
Use only correct blades. Do not
use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 7-1/4 in.
Before making a cut, be sure all adjustments are
secure.
Never touch blade
or other moving parts during use.
Double check all setups.
Make sure blade is tight
and not making contact with saw or workpiece before
connecting to power supply.
Firmly clamp or bolt
your tool to a workbench or table
at approximately hip height.
Make sure the miter table and saw arm (bevel function)
are locked in position before operating your saw.
Lock
the miter table by pushing the miter lock lever down. Lock
the saw arm (bevel function) by securely tightening the
bevel lock knob.
Содержание TSS702
Страница 103: ...NOTES NOTAS...