Ryobi RY34005, Руководство оператора

Страница: 10 / 50

8 — English
OXYGENATED FUELS
NOTICE: DO NOT USE E15 OR E85 FUEL IN THIS UNIT. IT
IS A VIOLATION OF FEDERAL LAW AND WILL DAMAGE
THE UNIT AND VOID YOUR WARRANTY.
NOTE:
Fuel system damage or performance problems
resulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated below are
not
covered under warranty.
Ethanol.
Gasoline containing up to 10% ethanol by volume
(commonly referred to as E10) is acceptable. E15 and E85
are not.
NOTICE:
Attempting to start the engine before it has been properly
filled with lubricant will result in equipment failure.
ADDING/CHECKING ENGINE LUBRICANT
See Figure 4.
Engine lubricant has a major influence on engine perfor-
mance and service life. This unit is shipped with a 20W50
engine lubricant to assist in the break-in period. For best
operating performance, continuing to use 20W50 engine
lubricant is recommended, however, SAE 30, 10W30, or
10W40 are all acceptable lubricants to use in this product.
Always use a 4-stroke engine lubricant that meets or exceeds
the requirements for API service classification SJ. Check
lubricant level before each use.
NOTE : Non-detergent or 2-stroke engine lubricants will
damage the engine and should not be used.
To add engine lubricant:

Remove the cap and seal from lubricant bottle
provided.

Unscrew the oil cap/dipstick and remove.

Using funnel provided, add entire bottle of engine lubricant
through oil fill hole.

Reinstall the oil cap/dipstick and secure.
To check engine lubricant level:

Set unit on a flat surface.

Wipe dipstick clean and re-seat in hole; do not
rethread.

Remove dipstick again and check lubricant level. Lubricant
level should fall within the hatched area on the dipstick.

If level is low, add engine lubricant until the fluid level
rises to the upper portion of the hatched area on the
dipstick.

Replace and secure the oil cap/dipstick.
NOTICE:
Do not overfill. Overfilling the crankcase may cause
excessive smoke, oil loss and engine damage.
OPERATING THE POWER HEAD
See Figure 5.
WARNING:
Engine housing may become hot during operation. Do
not rest or place your arm, hand, or any body part against
the engine housing during operation. Only hold the unit
as shown in Figure 5 during trimmer operation with all
body parts clear of engine housing (or as shown in the
applicable attachment Operator’s Manual). Extended
contact with the engine housing may result in burns or
other injuries.
WARNING:
Always position the unit on the operator’s right side. The
use of the unit on the operator’s left side will expose
the user to hot surfaces and can result in possible burn
injury.
WARNING:
To avoid burns from hot surfaces, never operate unit with
the bottom of the engine above waist level.
Hold the power head with your right hand on the rear handle
and your left hand on the front handle. Keep a firm grip with
both hands while in operation. Power head should be held
at a comfortable position with the rear handle about hip
height.
Always operate power head at full throttle. If debris becomes
wrapped around the attachment, STOP THE ENGINE,
disconnect the spark plug wire, and remove the debris.
Prolonged cutting at partial throttle will result in lubricant
dripping from the muffler.
WARNING:
Always hold the power head away from the body keeping
clearance between the body and the product. Any
contact with the attachment cutting head can result in
burns and/or other serious personal injury.
WARNING:
Extreme care must be taken when using a blade attachment
to ensure safe operation. Read the safety information for safe
operation when using a blade attachment and refer to the
safety rules and instructions in your attachment manual.
Improper operation of a blade or any attachment could
result in serious injury.
OPERATION