Safety, performance, and dependability have been given
top priority in the design of your trim router.
INTENDED USE
The trim router is intended for precision woodworking
tasks. The trim router is ideal for shaping the edge onto
wood and trimming laminates.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings and all instructions.
Failure
to follow the warnings and instructions may result in
electric shock,
fi
re and/or serious injury.
Save all warnings and instructions for future reference
.
TRIM ROUTER SAFETY WARNINGS
■
Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding
the work by your hand or against the body leaves it
unstable and may lead to loss of control.
■
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
■
Always use bits of the correct shank diameter that
are suitable for the speed of the product.
■
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool.
Following this rule will reduce the risk of
electric shock, fire, or serious injury.
■
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
■
Protect your lungs. Wear a face or dust mask if the
operation is dusty.
Following this rule will reduce the
risk of serious personal injury.
■
Protect your hearing. Wear hearing protection
during extended periods of operation.
Following this
rule will reduce the risk of serious personal injury.
■
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
■
Do not place battery tools or their batteries near
fire or heat.
This will reduce the risk of explosion and
possibly injury.
■
Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow.
A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
■
Batteries can explode in the presence of a source
of ignition, such as a pilot light.
To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
■
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
■
For best results, your battery tool should be
charged in a location where the temperature is
more than 10°C but less than 38°C. Do not store
outside or in vehicles.
■
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with soap
and water. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention.
Following this rule will
reduce the risk of serious personal injury.
■
Save these instructions.
Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
WARNING
Always feed the product into the workpiece against the
rotation direction of the bit. If feeding with the rotation
direction of the bit, the rotational force of the spinning bit
will tend to throw the tool away from the workpiece. This
could result in loss of control of the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
Injury caused by vibration
–
Limit exposure. See Risk Reduction.
■
Injury caused by flying debris
–
Wear eye protection at all times.
■
Injury caused by dust
1
English
|
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
Содержание R18TR
