background image

4 — English

OPERATION

WARNING:

Do not allow familiarity with products to make you 
careless. Remember that a careless fraction of a second 
is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1. Failure to do so could result in 
objects being thrown into your eyes resulting in possible 
serious injury.

APPLICATIONS

You may use this product for the following purpose:

 

Charging Ryobi

 18V Li-ion battery packs 

 NOTICE:

If at any point during the charging process none of the 
LEDs are lit, remove the battery pack from the charger 
to avoid damaging the product. DO NOT insert another 
battery. Return the charger and battery to your nearest 
authorized service center for service or replacement.

  NOTICE:

Charge in a well-ventilated area. Do not block charger 
vents. Keep them clear to allow proper ventilation.

KEY HOLE HANGER

See Figure 1, page 6.

To mount the charger, only use the key hole hanging feature. 

Screws should be installed so that the center distance is 

2-1/2 in.

CHARGING

See Figure 2, page 6.

Battery packs are shipped in a low charge condition to 
prevent possible problems. Therefore, you should charge 
them before first use. If the charger does not charge your 
battery pack under normal circumstances, return both the 
battery pack and charger to your nearest repair center for 
electrical check.

Charge time is approximately 1 hour, and is dependent upon 
the type of battery pack.

  Make sure the power supply is normal household voltage, 

120 volts, AC only, 60 Hz.

  Connect the charger to a power supply.

  Attach the battery pack to the charger by aligning the 

raised ribs on the battery pack with the grooves in the 
charger, then insert the battery pack into the charger.

  Press down on the battery pack to be sure contacts on 

the battery pack engage properly with contacts in the 
charger. Latches should snap into place to ensure charger 
is correctly connected.

  Do not place the charger in an area of extreme heat or 

cold. It will work best at normal room temperature. 

  The battery pack may become slightly warm to the touch 

while charging. This is normal and does not indicate a 
problem.

  After charging is complete, the green LED will remain on.

 

To remove the battery pack from the charger, depress 
latches and pull up on the battery pack.

 

When the battery pack is fully charged, remove it from 
the charger.

CHARGING A HOT BATTERY PACK

When using a tool continuously, the battery pack may 
become hot. A hot battery pack may be placed directly onto 
the charger port but charging will not begin until the battery 
temperature cools to within acceptable temperature range.  
When a hot battery pack is placed on the charger, the red 
LED will begin flashing and the green LED will be off.  When 
the battery pack cools, the charger will automatically begin 
charging.

CHARGING A COLD BATTERY PACK

A cold battery pack may be placed directly onto the charger 
port but charging will not begin until the battery temperature 
warms to within acceptable temperature range.  When a cold 
battery pack is placed on the charger, the red LED will begin 
flashing and the green LED will be off. When the battery 
pack warms, the charger will automatically begin charging.

Содержание P118B



















































































Отзывы: