Ruud 801MSP Series Скачать руководство пользователя | Manualshive

Страница: 48 / 52

background image

48

M

ai

nt

en

an

ce

MAINTENANCE

MAINTENANCE

FILTERS

LUBRICATION

IMPORTANT: DO NOT

attempt to lubricate the bearings on

the blower motor or the induced draft blower motor. Addi-
tion of lubricants can reduce the motor life and void the
warranty.

The blower motor and induced draft blower motor are per-
manently lubricated by the manufacturer and do not re-
quire further attention.

It is recommended that the blower motor and induced draft
blower motor be cleaned periodically by a qualified in-
staller, service agency, or the gas supplier to prevent the

possibility of overheating due to an accumulation of dust
and dirt on the windings or on the motor exterior. And, as
suggested elsewhere in these instructions, the air filters
should be kept clean. Dirty filters can restrict airflow. The
motor depends upon sufficient air flowing across and
through it to keep from overheating.

!

CAUTION

DO NOT OPERATE THE SYSTEM FOR EXTENDED PE-
RIODS WITHOUT FILTERS. A PORTION OF THE DUST
ENTRAINED IN THE AIR MAY TEMPORARILY LODGE
IN THE AIR DUCT RUNS AND AT THE SUPPLY REGIS-
TERS. ANY RECIRCULATED DUST PARTICLES WILL

BE HEATED AND CHARRED BY CONTACT WITH THE
FURNACE HEAT EXCHANGER. THIS RESIDUE WILL
SOIL CEILINGS, WALLS, DRAPES, CARPETS AND
OTHER HOUSEHOLD ARTICLES.

!

WARNING

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO
QUALIFIED SERVICE PERSONNEL FOR PROPER IN-
STALLATION, ADJUSTMENT AND OPERATION OF THIS
UNIT. READ THESE INSTRUCTIONS THOROUGHLY BE-
FORE ATTEMPTING INSTALLATION OR OPERATION.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RE-
SULT IN IMPROPER INSTALLATION, ADJUSTMENT,
SERVICE OR MAINTENANCE, POSSIBLY RESULTING IN

FIRE, ELECTRICAL SHOCK, CARBON MONOXIDE POI-
SONING, EXPLOSION, PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH.

DISCONNECT MAIN ELECTRICAL POWER TO THE
UNIT BEFORE ATTEMPTING ANY MAINTENANCE.
FAILURE TO DO SO CAN CAUSE ELECTRICAL
SHOCK RESULTING IN PERSONAL INJURY OR
DEATH.

«
...
46
47
48
49
50
...
»

Содержание 801MSP Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 801MSP Series

Бренд: ICP Страницы: 16

Бренд: barbas Страницы: 32

Бренд: Hotblast Страницы: 60

Бренд: GOLDBRUNN THERM Страницы: 27

Бренд: Lennox Страницы: 52

Бренд: Carrier Страницы: 5

Бренд: Empire Heating Systems Страницы: 16

Бренд: KDF Страницы: 31

Бренд: KEER Страницы: 34

Бренд: ICP Страницы: 27

58UVB PERFORMANCEt 96

Бренд: Carrier Страницы: 18

Бренд: American Standard Страницы: 20

Бренд: Weld Rite Страницы: 50

Бренд: Williams Страницы: 16

Бренд: Hitzer Страницы: 18

Бренд: Carbolite Страницы: 20

Бренд: Carbolite Gero Страницы: 23

Бренд: Carbolite Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды