Ruud 801MSP Series Скачать руководство пользователя | Manualshive

Страница: 37 / 52

background image

37

HIGH ALTITUDE

LP GAS AT HIGH ALTITUDES

LP GAS (TABLE 9)

NOTE:

Keep any parts removed during LP conversion procedure

stored with the product literature for future use.

LP Gas is a manufactured gas that has consistent heating value
across most regions.

The NFGC guidelines are used with the following exception:

The recommended LP Gas high altitude orifice selections differ
slightly in that the NFGC LP orifice chart, as they are not accurate
for these products. The National Fuel Gas Code LP orifices are

based on an 11" of water column pressure at the orifice, which dif-
fers from products that use 10" of water column at the orifice. This
difference requires a deviation from the NFGC orifice size recom-
mendations. The Sea Level input should still be reduced by 4%
per thousand ft. and the orifice size must be selected based on
the reduced input in Table 9.

Input (per Orifice

Altitude burner) 25000 Size

0 to 2000 ft. 25000 #54

2000*-3000* 24000 #54

3000*-4000* 23000 #54

4000*-5000* 22000 #54

5000*-6000* 21000 #54

6000*-7000* 20000 #54

7000*-8000* 19000 #55

8000*-9000* 18000 #55

9000*-10000* 17000 #55

TABLE 9

LP GAS
IMPORTANT: 80+ MODELS ONLY! DO NOT
USE THIS CHART WITH ANY 90+ MODELS.

Hig

h A

ltitu

de

«
...
35
36
37
38
39
...
»

Содержание 801MSP Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 801MSP Series

Бренд: Lennox Страницы: 7

Бренд: Lennox Страницы: 28

Бренд: Lennox Страницы: 51

Бренд: Lennox Страницы: 61

EL195UH040NE36B

Бренд: Lennox Страницы: 50

EL296DF045XE36B

Бренд: Lennox Страницы: 65

Бренд: Scotty Страницы: 28

Бренд: SCOTTY SS Страницы: 49

Бренд: CAC / BDP Страницы: 84

CASSARA TEAK 20127A

Бренд: Frontage Страницы: 3

Бренд: Carrier Страницы: 10

Бренд: Carrier Страницы: 22

Бренд: COZY Страницы: 73

Бренд: York Страницы: 8

Бренд: York Страницы: 12

Бренд: Fedders Страницы: 32

Бренд: York Страницы: 16

Бренд: ICP Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды