Ruud 801MSP Series Скачать руководство пользователя | Manualshive

Страница: 13 / 52

background image

13

HORIZONTAL UNITS

1. Position the unit to minimize long runs of duct or runs of

duct with many turns and elbows.

2. Unit can be mounted left or right side airflow configura-

tion.

3. Position the unit on adequate supports or by using sup-

port brackets (see Figure 8) and connect supply plenum.

4. If summer air conditioning is desired, position the indoor

coil on the supply air side of the unit. Insure that no air
can bypass this coil.

5. Secure the four angle brackets (shipped with (-)801P

units) to the return air opening. See Figure 9. Connect
the return air ducting to the return air opening at the top
of the unit. Make the connection air tight to prevent en-
training combustion gases from an adjacent fuel-burning
appliance.

NOTE: Do not block furnace access with support rods.
Maintain clearances recommended in Figure 8. Allow
enough space for proper service maintenance or re-
placement of the heat exchanger and blower assembly.

DUCTING

FOUR ANGLE BRACKETS, SHIPPED WITH (-)801P UNITS, CAN BE
INSTALLED HORIZONTALLY. THESE BRACKETS MAY BE USED TO
SECURE THE RETURN AIR DUCT TO A HORIZONTAL UNIT.

RETURN

AIRFLOW

REAR VIEW

FIGURE 9

HORIZONTAL RETURN AIR DUCT
(LEFT-HAND AIRFLOW POSITION SHOWN)

NOTE:

HORIZONTAL LEFT ORIENTATION DEPICTED IN ILLUSTRATION.
HORIZONTAL RIGHT ORIENTATION IS SIMILAR IN INSTALLATION.

AIR FLOW

NOTE:
DO NOT BLOCK FURNACE ACCESS WITH
SUPPORT RODS, ALLOW SPACE FOR
PROPER SERVICE MAINTIENCE OR
REPLACEMENT OF THE HEAT EXCHANGER
AND BLOWER ASSEMBLY .

FIGURE 8

HORIZONTAL FURNACE INSTALLED W/SUPPORT BRACKETS

ST-A1220-03

Du

ctin

g

«
...
11
12
13
14
15
...
»

Содержание 801MSP Series





















































Отзывы:

Нет отзывов

Похожие инструкции для 801MSP Series

Бренд: York Страницы: 24

Бренд: Thermo Pride Страницы: 44

Бренд: CSA Страницы: 100

zirkonofen 600/V3

Бренд: Zirkon zahn Страницы: 40

Бренд: Bryant Страницы: 2

Бренд: Johnson Controls Страницы: 41

Energy Master II 710

Бренд: Hitzer Страницы: 17

Бренд: York Страницы: 8

Бренд: Bard Страницы: 59

Бренд: ICP Страницы: 60

Бренд: USSC Страницы: 32

Бренд: Unitary products group Страницы: 4

ALL RESIDENTIAL MULTI-POSITION 356486-UUM-H-0609

Бренд: Johnson Controls Страницы: 6

Бренд: Unitary products group Страницы: 4

Бренд: York Страницы: 16

CARBOLITE GERO GPC 12/200

Бренд: VERDER Страницы: 36

Carbolite HTF 17

Бренд: VERDER Страницы: 20

CARBOLITE GERO STF 15/180

Бренд: VERDER Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды