background image

·

 

 

 

2  Preparation before Installation 

 

To avoid body injury and equipment damage, please carefully read the safety suggestions before you install 

RSR30-X. 

 

The following safety suggestions do not cover all possible dangers. 

2.1  General Suggestions 

Routers are important network hops and their working affects the normal operation of the whole network. 

The following suggestions are advised for the installation and use of routers: 

 

Do not place the router in a wet place and prevent any liquid from entering into it. 

 

Install the router in a place away from heating sources 

 

Make sure the normal grounding. 

 

Wear anti-static wrist straps to install or maintain routers 

 

Do not plug/unplug routers' modules when power on 

 

Do not unplug routers' power cables when power on 

 

Do not wear loose clothes to avoid hooking any parts. Before operation, tighten your band, shawl, and sleeves. 

 

Put the tools and parts away from where people walk by. 

 

Use UPS to prevent power failure and other interferences 

2.1.1  Electrical Safety 

 

Please observe local regulations and specifications when performing electrical operations. Relevant operators 

must be qualified. 

 

Please carefully check for any potential danger in the working area, for example, ungrounded power supply, 

unreliable grounding of the power supply and damp/wet ground or floor. 

 

Find out the location of the emergency power supply switch in the room before installation. First cut off the power 

supply in case of an accident. 

 

Be sure to make a careful check before you shut down the power supply. 

 

Do not place the equipment in a damp/wet location. Do not let any liquid enter the chassis 

 

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electrical attack, thus 

causing severe even fatal damages to human bodies and equipment. 

 

Direct or indirect touch through a wet object on high-voltage and mains supply can bring a fatal danger. 

2.1.2  Laser Safety 

Among the modules supported by RG-N18000, there are a great number of optical modules that are Class I laser 

products. 

Precautions: 

Содержание RSR30-X-SPU10



























Отзывы: