Ruijie RG-ES100 Series Скачать руководство пользователя страница 35

Страница: 35 / 41

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide

Appendix B Mini-GBIC and SPF+ Module

Tools: Cross or straight screwdriver, Multimeter, Diagonal pliers

Installation Steps:

1. Tear one side of the protection paper for the double-sided adhesive tape and paste the tape to the framework of the

Ethernet port arrester. Tear the other side of the protection paper for the double-sided adhesive tape and paste the

Ethernet port arrester to the switch framework. The paste location for the Ethernet port arrester shall be as close to

the grounding terminal of the switch.

2. Based on the distance of the switch grounding terminal, cut the grounding line for the Ethernet port arrester and firmly

tighten the grounding line to the grounding terminal of the switch.

3. Use the multimeter to check whether the grounding line for the arrester is in good contact with the switch grounding

terminal and the framework.

4. According to the description on the Ethernet Port Arrester Hardware Installation Guide, connect the arrester using the

adapter cable(note that the external network cable is connected to the end of IN, while the adapter cable connected to the

switch is connected to the end of OUT) and observe whether the LED on the board is normal or not.

5. Use the nylon button to bundle the power cables.

Figure C-2 Schematic Diagram for the Ethernet port Arrester Installation

The Ethernet port arrester is only for the 10M/100M copper Ethernet ports with the RJ-45 connector;

The Ethernet port arrester is not provided, the user can purchase them to address their own practical requirements.

For the detailed information during the arrester installation, please refer to Ethernet Port Arrester Hardware

Installation Guide, which contains the technical specification and the maintenance and installation of the arrester.

You may pay attention to the following conditions during the actual installation to avoid influencing the performance of the

Ethernet port arrester:



Reversed direction of the arrester installation. You shall connect the external network cable to the “IN” end and
connect the switch Ethernet port to the “OUT” end.

Содержание RG-ES100 Series










































Результаты поиска

Содержание RG-ES100 Series

Отзывы:

Похожие инструкции для RG-ES100 Series

Бренды по названию

Популярные бренды

Ruijie RG-ES100 Series, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание RG-ES100 Series

Отзывы:

Похожие инструкции для RG-ES100 Series

Бренды по названию

Популярные бренды