Ruijie RG-ES100 Series Скачать руководство пользователя страница 6

Страница: 6 / 41

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide

Product Overview

Front Panel

Figure 1-2 Front Panel of RG-ES109G-LP-L

Note:

1. System status LED

2. Port Mode LED Switch-Over Button

3. Copper port status LED

4. 10/100/1000Base-T auto-sensing Ethernet port

5. Copper port status LED

6. 10/100/1000Base-T auto-sensing Ethernet port

Back Panel

Figure 1-3 Back Panel of RG-ES109G-LP-L

Note:

1. Grounding pole

2. Working Mode Switch-Over Button

3. Power port

4. Hole for anti-theft lock

Heat Dissipation

The RG-ES109G-LP-L adopts natural heat dissipation, thereby ensuring normal function of the device in the specified

environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to allow air

circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents.

LEDs

LED

Panel Identification

State

Meaning

System status LED

Status

Off

The switch is not receiving power.

Содержание RG-ES100 Series










































Результаты поиска

Содержание RG-ES100 Series

Отзывы:

Похожие инструкции для RG-ES100 Series

Бренды по названию

Популярные бренды

Ruijie RG-ES100 Series, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание RG-ES100 Series

Отзывы:

Похожие инструкции для RG-ES100 Series

Бренды по названию

Популярные бренды