background image

Ruijie RG-ES100 Series Switches Hardware Installation and Reference Guide                                 

Product Overview 

Blinking green 

The  PoE  power  exceeds  the power  of  the  entire 

device (54 W). The new connected PD cannot be 

powered  up  due  to  insufficient  power.  The 

switching function is operational. 

Solid green 

The switch is operational. 

RJ45 port PoE status 

LED 

1-8 

Off 

PoE is not enabled. 

Solid green 

PoE is enabled. The port is operational. 

Blinking green 

Indicates PoE overload.   

 

1000Mbps RJ-45 port 

status LED 

1-9 

Off 

The port is not connected. 

Solid green 

The port is connected at 10/100/1000 Mbps. 

Blinking green 

The  port  is  receiving  or  transmitting  traffic  at 

10/100/1000 Mbps. 

1.2  RG-ES126G-P-L 

Technical Specifications 

Model 

RG-ES126G-P-L 

Optical Module 

For details, see Appendix B. 

 

The supported module type may change at any time. Consult us for the latest information. 

SFP Port 

Supports 1000Base-X modules. 

Power Supply 

 

AC input 

Rated voltage range: 100V to 240V 

Maximum voltage range: 90V to 264V 

Frequency: 50/60 Hz 

Rated current: 6A 

Power cord requirement: 10A 

EEE 

Not supported 

PoE 

Supports PoE and PoE+. 

Ports 1-24 are PoE/PoE+-capable with the maximum power output of 30W per port.   

Ports 25 and 26 do not support PoE or PoE+.   

The overall maximum output power of PoE/PoE+ is 370W. 

PoE Mode 

Mode A (data pairs 1-2 and 3-6) 

Power 

Less than 25W with no PoE load 

Содержание RG-ES100 Series










































Отзывы: