Ruhle SR 1 Turbo Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 19

background image

Cutting machine SR 1 / SR 1 Turbo

8

2.1

Machine transport and setup

Please refer to the short instructions supplied with the machine
regarding transport and setup of the cutting machine.

The machine and machine parts must be transported by 2
persons (1x operator of floor conveyor / 1x transport
supervision).

The power supply line must not be damaged by driving
over or pinching it!

The machine must be decommissioned until a damaged
power supply line has been repaired!

Make sure the machine is stable!

The machine may not be set up in an elevated position!

2.2

Workplace description

Swivel range of
knife protection
box

Swivel range
of hood (tool
magazine)

«
...
6
7
8
9
10
...
»

Содержание SR 1 Turbo




















Отзывы:

Нет отзывов

Похожие инструкции для SR 1 Turbo

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: FENDT Страницы: 31

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды