rtd DM35425 Скачать руководство пользователя

Страница: 52 / 60

RTD Embedded Technologies, Inc.

www.rtd.com

DM35425HR User’s Manual

6.6.7

EXT_CLK_EDGE

EAD

RITE

)

Selects which edge detect to trigger on. This is a bit settable register.

0= Rising Edge Detect, 1= Fall Edge Detect.

6.6.8

EXT_CLK_PW

EAD

RITE

)

This register is used to increase the pulse width of the clock. When set to 0x00 the pulse width is high for 25ns. By incrementing this register by
0x01 the pulse width stays high for additional 25ns.

NOTE: If EXT_CLK_PWn is set to be wider than the EXT_CLKn_CFG Clock

Frequency the signal will just stay high.

6.6.9

EXT_CLK

_CFG

EAD

RITE

)

Selects clocking method.

B[7:0]:

0x00:

Disables External Clocking.

0x80:

Not Gated: EXT_CLKn will be inputted/outputted independent of the EXT_CLK_GATEn corresponding gate value.

0x81:

Clock Gated (High): EXT_CLKn will be inputted when the EXT_CLK_GATEn corresponding gate value is high, this

doesn’t affect when

outputting a clock.

0x82:

Clock Gated (Low): EXT_CLKn will be inputted when the EXT_CLK_GATE

n corresponding gate value is low, this doesn’t

affect when outputting a clock.

Содержание DM35425





























































Результаты поиска

Содержание DM35425

Отзывы:

Похожие инструкции для DM35425

Бренды по названию

Популярные бренды

rtd DM35425, Руководство пользователя

Результаты поиска

Содержание DM35425

Отзывы:

Похожие инструкции для DM35425

Бренды по названию

Популярные бренды