RSI VIDEO TECHNOLOGIES XT600i Скачать руководство пользователя страница 9

Страница: 9 / 44

2011/11/10 Ed 1.5

Setup and Programming manual for XT series GPRS

9 |

P a g e

4455 White Bear Parkway, Suite 700

White Bear Lake, MN 55110

XT Programming

CMA Programming Device/Keypad

Reset the XT Panel:

Press and hold programming button (



) for 10sec until the

Indicator LED blinks twice

Press and instantly release the programming button (



The indicator LED will blink once. The panel is now in ‘Learn

Mode’ for the CMA601 keypad.

CLR & ESC/NO

<======XX======>

Insert all three batteries into the CMA601 and press both the

ESC/NO and CLR keys at the same time and release. The

indicator LED on the keypad will blink rapidly.



YES

KEYPAD 1
RECORDED

www.RsiAlarm.com

<- LANGUAGE : ->

ENGLISH





for language selection



YES to apply

Other languages are available by scrolling with arrows.

ITALIANO, NEDERLANDS, DEUTSCH, CASTELLANO,

SVENSKA, PORTUGUES, FRANCAIS

Press YES for the selected one.



*Note: If you are having issues
pairing the keypad to the panel,
please refer to the troubleshooting
section.

Содержание XT600i













































Результаты поиска

Содержание XT600i

Отзывы:

Похожие инструкции для XT600i

Бренды по названию

Популярные бренды

RSI VIDEO TECHNOLOGIES XT600i, Полное руководство по установке и программированию

Результаты поиска

Содержание XT600i

Отзывы:

Похожие инструкции для XT600i

Бренды по названию

Популярные бренды