RSF Energy OPEL 2000 Скачать руководство пользователя

Страница: 26 / 40

OPEL 2000

Figure 23: Gravity vent clearances

4 min.

2 min.

front view

B vent starter(s)

here

grille and adapter

optional gravity

vent outlet

4 min.

59 min.

side view

59 min.

min.

59 min.

2 min.

B vent starter

Figure 22: Gravity vent kit (FD-V)

grille adapter

rear side

grille

REMOTE VENTING

The gravity vent system can distribute air to an upper

level or a room next door without an extra blower. If you

use two gravity vent kits you may block off the upper

louver area with the desired facing. The central heat option

allows heat to be sent up to 50 ft. away. Figure 21

illustrates various certified ways of incorporating the two

systems.

THE GRAVITY VENT SYSTEM (FD-V)

The FD-V Kit includes:

- A grille

- A grille adaptor

- A B-vent starter section

- A shut-off damper (do not use with

upper louvers blocked)

IMPORTANT: No substitution of any of these parts is

allowed. These genuine RSF ENERGY parts have the

correct clearances. These clearances must be

maintained for your safety.

The FD-V system incorporates standard 8" B-vent

components for installation. Single wall pipe is not

allowed due to the high temperature of the air in a gravity

vent system. Any listed brand of 8" B-vent pipe may be

used and is not a part of the FD-V. The maximum pipe

length is 15 ft. from the top of the fireplace to the outlet.

The B-vent components can be replaced by UltraBlack

double wall black connector made by ICC only.

NOTE: If two gravity vent lines are installed, then two

FD-V kits must be ordered.

Figure 23 indicates the minimum clearances and framing

dimensions. Passing through a combustible wall or

Содержание OPEL 2000









































Результаты поиска

Содержание OPEL 2000

Отзывы:

Похожие инструкции для OPEL 2000

Бренды по названию

Популярные бренды

RSF Energy OPEL 2000, Руководство пользователя

Результаты поиска

Содержание OPEL 2000

Отзывы:

Похожие инструкции для OPEL 2000

Бренды по названию

Популярные бренды