Roto-Mix Roto-Spread 532-16 страница 16 Скачать руководство пользователя

Страница: 16 / 49

OPERATION

DO NOT CLIMB ON OR ENTER

THE SPREADER WHILE IN OPERATION.

CLEAR THE AREA OF ALL PER-

SONS BEFORE BEGINNING OPERATION.

TRACTOR HOOKUP

See figure 4.

Back tractor so draw bar aligns with spreader

hitch. Put tractor in PARK, set park brake and

turn off engine before dismounting.

Connect the spreader hitch to the tractor drawbar

with a 1-1/4” hitch pin. The hitch pin must have a

security clip or retainer to prevent it from

accidentally coming out of the hitch.

Install safety chain around tractor drawbar

support and secure with safety latched grab

hook. See figure 3.

Crank the spreader jack completely up.

Remove the pair of hydraulic hoses coming from

the spreader hydraulic pump from their storage

bracket and connect the ends a tractor port. See

Understand The Controls on page 13 for

recommended connection.

Remove the pair of hydraulic hoses coming from

the spreader rear gate hydraulic cylinders from

their storage bracket and connect the ends a

tractor port. See Understand The Controls on

page 13 for recommended connection.

Unhook the PTO storage chain from the slotted

storage bracket and slide the PTO drive shaft

yoke onto the splined tractor PTO shaft. Be sure

the yoke securely snaps onto the retention

groove of the tractor shaft.

Connect the PTO Guard anchor chain to the

anchor loop on the spreader hitch.

Place the PTO storage chain back in the slotted

storage bracket so it does not dangle.

10. Remove wheel chocks.

NEVER OPERATE SPREADER

WITH ANY GUARDS OR SHIELDS REMOVED. FAIL-

URE TO HEED MAY RESULT IN SERIOUS PER-

SONAL INJURY OR DEATH.

LOADING

SPREADER MUST BE HITCHED

TO TRACTOR FOR LOADING. THE JACK CAN NOT

SUPPORT THE LOADED SPREADER WEIGHT

AND/OR UNEXPECTED “TIP UP” OF THE

SPREADER CAN RESULT.

Park the spreader for loading. Put the tractor in

PARK or NEUTRAL and apply the parking brake.

Close the hydraulic rear gate before loading.

It is unlawful to allow any manure spillage to

occur on public roadways. Be sure rear gate is

fully closed and sliding gate scrapers are

adjusted so no liquid leakage occurs. Do not

heap load such that manure is allowed to fall off

spreader during transporting on roadways.

Load the spreader. The moisture content will

determine how full it can be loaded. See

SPECIFICATIONS for capacity. Solid manure

can generally be loaded level to slightly heaped.

High moisture slurries are heavier and loading

may be limited.

Page 16

FIGURE 4. TRACTOR HOOK UP

PTO

STORAGE

CHAIN

HOSE END

STORAGE

SLOT

BELT

DRIVE

HOSES

JACK

PTO GUARD ANCHOR CHAIN

REAR GATE

HOSES

Содержание Roto-Spread 532-16


















































Результаты поиска

Содержание Roto-Spread 532-16

Отзывы:

Похожие инструкции для Roto-Spread 532-16

Бренды по названию

Популярные бренды

Roto-Mix Roto-Spread 532-16, Руководство пользователя, инструкции по установке и каталог запчастей

Результаты поиска

Содержание Roto-Spread 532-16

Отзывы:

Похожие инструкции для Roto-Spread 532-16

Бренды по названию

Популярные бренды