Rossum Control Forge Скачать руководство пользователя страница 23

Страница: 23 / 70

Initially turning the knob brings the

Level

value to the fore on the display and modifies
it. While the

Level

value is displayed, you can

use the encoder to fine tune your selection.

NOTE:

While the value is displayed for

editing, press, hold, and turn the encoder

to quantize the selected value to even while
volts. Release the encoder to continue editing
if desired.

ANOTHER NOTE:

If, while the

Level

value

is displayed, you hold the

Mode/Quantize

button and turn the

Level

knob, the resulting

values will be quantized to exact semitones
(i.e., 1/12

volt) and displayed as octaves and

semitones (e.g., “+2 oct +06 semi”). Once the
editing display is dismissed, the

Level

value on

the main display will be in the format of the
currently selected mode (see below).

YET ANOTHER NOTE:

To tweak a previously

programmed

Level

value (without having

to wiggle the knob and change the setting),
with no parameter editing box visible, click the
encoder to display the current value of the
segment’s

Time

Level

(whichever was most

recently edited). If that’s the Time rather than
the Level parameter, click the encoder twice
more dismiss the

Time

parameter and display

the

Level

parameter.

Once modified, the display can be dismissed
by:

Pressing the encoder button
Selecting another parameter to edit

Mode/Quantize Button

Sequentially pressing this button cycles
through the four available

Level Modes.

The

current mode appears on the main display.
An associated LED lights to indicate whether
the current mode is

Absolute

Relative.

The four modes are:

Absolute (Abs):

The

Target Level

for the

segment is the level set by the

Level Knob.

Absolute Quantized (AbsQ):

The

Target

Level

for the segment is the level set by

the

Level Knob

quantized to the nearest

1/12

volt, displayed as octaves and

semitones.

Relative (Rel):

The

Target Level

for the

segment is the sum of the ending level of
the previous segment and the level set by
the

Level Knob.

Relative Quantized (RelQ):

The

Target

Level

for the segment is the sum of the

ending level of the previous segment
and the the level set by the

Level Knob,

quantized to the nearest 1/12

volt,

displayed as octaves and semitones.

NOTE:

In either

Relative Mode,

if the

resulting level would be above +5V or

below -5V, the actual target is set at +5V or -5V.

A Relative Mode Example:

Assume Segment

2 is in

Relative Mode

and its

Level

is +1.000

volt.

If Segment 1 has a

Target Level

of +1.500

volts and is followed by Segment 2, the
actual

Target Level

of Segment 2 would be

+2.500 volts.

However, if Segment 2 is instead jumped to
from Segment 6, which has a

Target Level

of -2.250 volts, the actual

Target Level

Segment 2 would then be -1.250 volts.

The point being that a Segment in

Relative

Mode

can have radically different effective

Target Levels

depending on its immediately

previous segment.

NOTE:

The quantization function also

affects any external CVs that are routed

to the output via one of the CV Passthrough
shapes.

Содержание Control Forge






































































Результаты поиска

Содержание Control Forge

Отзывы:

Бренды по названию

Популярные бренды

Rossum Control Forge, Руководство по эксплуатации

Результаты поиска

Содержание Control Forge

Отзывы:

Бренды по названию

Популярные бренды