manualshive.com logo in svg

Rossum Control Forge, Руководство по эксплуатации

Поделиться
Скачать
Rossum Control Forge Скачать руководство пользователя страница 10

10 

|

Additionally, the CVs at these inputs are 
passed directly through to the output during 
any segment whose shape is 

CV 1

 or 

CV 2

 

Passthrough

.

Time Scale CV

This input accepts CVs in the range of -5V 
to +5V. Voltages outside of that range are 
clipped to the appropriate limit.

The value of the CV modifies the 

Time

 values 

of all of a preset’s segments such that a 1 volt 
change increases the Time Scale Rate value 
by a factor of 2. Therefore, overall range of 
modification is from 1/32 of the set time to 
32 times the set time.

In Play Mode, the 

Encoder

 also controls 

time scale. Its value is multiplied by the Time 
Scale CV to provide the final time scale 
modification value.

Sequencer Dec, Inc, and Reset

Depending on the Preset Sequencer state, 
rising edges at these inputs control the 
loading of a sequence’s programmed presets. 
See 

Chapter 17

 for details.

Outputs

+ Output

Outputs the CV contour in the 
range of -5V to +5V. Accuracy is 
approxi/-1mV.

- Output

Outputs a precisely inverted 
version of the CV contour in the 
range of -5V to +5V.

Trigger 1

Outputs a +10V trigger or gate 
pulse whenever the condition 
set in the 

Assign Trigger 1

 menu 

is met or the 

Conditional Value/

Trigger 1

 button is pressed while 

in Play Mode.

Trigger 2

Outputs a +10V trigger or gate 

pulse whenever the condition set in the 

Assign Trigger 2

 menu is met or the 

Assign 

Triggers/Trigger 2

 button is pressed while in 

Play Mode.

Controls

Data/Time Scale Encoder

The Encoder is used 
in 

Program Mode

 

to set the values of 
parameters selected 
via the parameter 
push buttons or 
knobs. 

The Encoder 

includes an integrated pushbutton that is 
typically used to enter the currently selected 
value (see individual parameters for details).

In 

Play Mode,

 the encoder serves as a real 

time control over Time Scale. The time scale 
range is between X 0.031 and X 32X in 80 
approximately logarithmic steps. Pressing 
and holding the encoder switch and turning 
it quantizes the Time Scale values to factors 
of 2.

Global/Pause/Utilities Button

In 

Play Mode,

 if Control Forge is running, 

quickly pressing this button causes playback 
to pause. Pressing it again causes playback to 
resume from the paused location. Pressing 
and holding this button brings up the 

Utilities 

Menu

 described in 

Chapter 18.

In 

Program Mode,

 quickly pressing this button 

brings up the 

Preset Globals

 menu described 

in 

Chapter 8.

 If Control Forge is running, 

pressing and holding this button causes 
pausing and resuming playback.

NOTE: 

Yes, we realize the short press/long press 

functionality is reversed between Play and 

Program Modes. While we prefer things 
to be consistent, after long discussion we 
came to the conclusion that it was more 

important that the things you were most most 
likely to do in each mode were accessed with a 
short press.

Manual Gate Button

Содержание Control Forge







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды