background image

10 • Introduction

QRA-8808 User Guide (v5.0)

Menu Sequences

Menu arrows are used in procedures to identify a sequence of menu items that you must follow. For example, if a 
step reads “

File

 > 

Save As

,” you would click the 

File

 menu and then click 

Save As

.

Important Instructions

Star icons are used to identify important instructions or features. For example:

Contact your IT department before connecting to your facility network to ensure that there are no conflicts. They 
will provide you with an appropriate value for the IP Address, Subnet Mask, and Gateway for your device.

Contacting Technical Support

At Ross Video, we take pride in the quality of our products, but if problems occur, help is as close as the nearest 
telephone.

Our 24-hour Hot Line service ensures you have access to technical expertise around the clock. After-sales service 
and technical support is provided directly by Ross Video personnel. During business hours (Eastern Time), 
technical support personnel are available by telephone. After hours and on weekends, a direct emergency technical 
support phone line is available. If the technical support person who is on call does not answer this line immediately, 
a voice message can be left and the call will be returned shortly. This team of highly trained staff is available to 
react to any problem and to do whatever is necessary to ensure customer satisfaction.

Technical Support

: (+1) 613-652-4886

After Hours Emergency

: (+1) 613-349-0006

E-mail

[email protected]

 

Website

http://www.rossvideo.com

 

Содержание QRA-8808

































Отзывы: