background image

QRA-8808 User Guide (v5.0)

Physical Installation • 15

Physical Installation

This chapter provides instructions for installing the rear module for your QRA-8808, installing the card in the 
frame, cabling details, and how to upgrade the software on your card(s).

Before You Begin

Before proceeding with the instructions in this chapter, ensure that your openGear frame is properly installed 
according to the instructions in its manual.

Static Discharge

Throughout this chapter, please heed the following cautionary note: 

Unpacking

Unpack each card you received from the shipping container and ensure that all items are included. If any items are 
missing or damaged, contact your sales representative or Ross Video directly. 

Installing the QRA-8808

The QRA-8808 can be installed in the DFR-8321, the OG3-FR, and the OGX-FR series frames using the supported 
rear module.

Supported Rear

The 

8320AR-302

 Full Rear Module is required.

Installing a Card

You must first install the rear module in the frame and then install the card in the appropriate slot within an 
openGear frame. This section outlines how to perform both tasks.

To install the rear module in the openGear frame

1. Ensure that the frame is properly installed according to the instructions in its manual.

2. On the rear of the frame, locate the card frame slot.

3. Remove the Blank Plate from the rear of the slot you have chosen for card installation. 

4. Seat the bottom of the rear module in the seating slot at the base of the frame’s back plane. (

Figure 4.1

)

5. Align the top hole of the rear module with the screw hole on the top edge of the frame back plane.(

Figure 4.1

)

6. Using a Phillips screwdriver and the supplied screw, fasten the rear module to the back plane. Do not 

over-tighten. 

ESD Susceptibility

 — Static discharge can cause serious damage to sensitive semiconductor 

devices. Avoid handling circuit boards in high static environments such as carpeted areas and when 
synthetic fiber clothing is worn. Always exercise proper grounding precautions when working on circuit 
boards and related equipment.

Notice

 — Ensure that you install the QRA-8808 using the supported rear module listed below. 

Installing the QRA-8808 with an unsupported rear module can damage the card, the rear module, or 
both.

Содержание QRA-8808

































Отзывы: