background image

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his own expense. 

Canada

This Class “A” digital apparatus complies with Canadian

 

ICES-003 and part 15 of the FCC Rules.

Cet appareil numerique de la classe “A” est conforme a la norme NMB-003 du Canada.

European Union

This equipment is in compliance with the essential requirements and other relevant provisions established under 
regulation (EC) No 765/2008 and Decision No 768/2008/EC referred to as the “New Legislative Framework”. 

Australia/New Zealand

This equipment is in compliance with the provisions established under the Radiocommunications Act 1992 and 
Radiocommunications Labeling (Electromagnetic Compatibility) Notice 2008.

Korea

This equipment is in compliance with the provisions established under the Radio Waves Act.

Class A equipment (Broadcasting and communications service for business use)

This device is a business-use (Class A) EMC-compliant device. The seller and user are advised to be aware of this 
fact. This device is intended for use in areas outside home.

International

This equipment has been tested under the requirements of CISPR 22:2008 or CISPR 32:2015 and found to comply 
with the limits for a Class A Digital device. 

Maintenance/User Serviceable Parts

Routine maintenance to this openGear product is not required. This product contains no user serviceable parts. If 
the module does not appear to be working properly, please contact Technical Support using the numbers listed 
under the “

Contact Us

” section of this manual. All openGear products are covered by a generous 5-year warranty 

Notice

 — Changes or modifications to this equipment not expressly approved by Ross Video Ltd. could 

void the user’s authority to operate this equipment.

Warning

 — This equipment is compliant with Class A of CISPR 32. In a residential environment this 

equipment may cause radio interference.

Notice

 — This is a Class A product. In domestic environments, this product may cause radio 

interference, in which case the user may have to take adequate measures.

Type of Equipment 

User’s Guide 

A

̗ ̛̛

(

߶הࡈ ؏ܞ੼ݦ̛࢕ࢢ

)

Class A Equipment 
(Industrial Broadcasting & 
Communication Equipment) 

ࢇ ̛̛Е ߶הࡈ

(A

̗

)

ࢷ࢕ળࢶଢ̛̛Ի۰ શ

֐࢕ ӖЕ یࡈ࢕Е ࢇ ࢺࡶ ࣯ࢂଜݤ̛ ؂Ԃ

ֲ

,

ɼࢽ࠹ࢂ एࠇ߾۰ یࡈଜЕ ʨࡶ ּࢶࡳԻ

ଢТЬ

.

This equipment is 

Industrial (Class A) 

electromagnetic wave suitability equipment

 and 

seller or user should take notice of it, and this 
equipment is to be used in the places except for home. 

Содержание QRA-8808

































Отзывы: