Ross NK RCP-NKM Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

Ross NK RCP-NKM Скачать руководство пользователя страница 17

RCP-NKM User Guide (v3.0)

Installation • 3–3

Figure 3.3

Remote control panels connected to NK Series equipment in a star layout

To connect the remote control panel in a star layout

1.

Install the RCP-NKM into the rack frame, then fix in place with appropriate fasteners.

2.

Connect a straight CAT5 Ethernet cable between a

T-Bus

connector on the rear panel of the RCP-NKM and a

T-Bus

connector on the rear panel of the NK-IPS (see

).

3.

Connect the 5 V 2 A power supply provided to the

POWER

connector on the rear panel of the RCP-NKM.

4.

Connect the cable from the power supply to a suitable AC mains supply.

5.

Connect any remaining remote control panels in this manner.



The RCP-NKM is designed for installation into a standard 19" equipment rack. It has integrated rack ears,
allowing it to be screwed in using standard screws and cage nuts.

Connecting to the NK-IPS in the Routing Switcher System

Before you can set up and send a configuration document to the RCP-NKM, you must connect an NK-IPS to the
RCP-NKM. Once DashBoard locates the NK-IPS, the attached RCP-NKM is visible and can have configuration
documents sent to it.

Most systems automatically detect an NK-IPS if its IP address uses the same subnet as the PC running DashBoard.
However, if the device is not detected automatically, follow the steps below. For information on the NK-IPS, refer
to the documentation provided with the equipment.

To connect to the NK-IPS

1. Launch DashBoard.

2.

Use Walkabout to determine and/or change the IP address of the NK-IPS. Refer to the

NK-IPS User Guide

for

more information.

3.

From the main toolbar in DashBoard select

File

>

New

>

NK IPS Connection

.

NK-IPS
Network Bridge

RCP-NKM
Remote Control Panel

Routing Switcher

Appropriate

NK Series

power supply

T-BUS

NK Series

5 V, 2 A

powersupply

Routing Switcher

RCP-NKM
Remote Control Panel

RCP-NKM
Remote Control Panel

RCP-NKM
Remote Control Panel

NK Series

5 V, 2 A

powersupply

NK Series

5 V, 2 A

powersupply

NK Series

5 V, 2 A

powersupply

Appropriate

NK Series

power supply

T-BUS

T-BUS

T-BUS

Appropriate

NK Series

power supply

T-BUS

T-BUS

«
...
15
16
17
18
19
...
»

Содержание NK RCP-NKM

























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды