Rosemount 2120 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 72

background image

Reference Manual

00809-0100-4030, Rev DA

June 2007

Rosemount 2120

B-14

International Electrotechnical Commission (IEC) Approvals

IECEx Flame Proof Approvals

E7

Certificate: IECEx SIR 06.0051
Flame Proof and Dust:
Zone 0/1
Ex d IIC T6 (Tamb -40°C to +75°C)
Ex tD A21 T85°C (Tamb -40°C to +75°C) IP6X

Instructions specific to hazardous area installations

1. The equipment may be used with flammable gases and vapors with apparatus groups

IIA, IIB & IIC and with temperature classes T1, T2, T3, T4, T5 & T6.

2. The equipment is certified for use in ambient temperatures of -40°C to +80°C and with a

maximum process temperature of 150°C.

3. Installation of this equipment shall be carried out by suitably trained personnel, in

accordance with the applicable code of practice.

4. Inspection and maintenance of this equipment shall be carried out by suitably trained

personnel, in accordance with the applicable code of practice.

5. The user should not repair this equipment.

6. The certification of this equipment relies upon the following materials used in its

construction:
Body: Aluminum Alloy (ASTM B26 356-T6, LM25 TF, or A360.0), or St. Steel 316C12
Lid: Aluminum Alloy (ASTM B26 356-T6, LM25 TF, or A360.0), or St. Steel 316C12
Switch: Stainless steel 316 Type or Hastelloy C276 UNS N10276 or equivalent
Switch Filling: Perlite
Lid Seal: Silicone

If the equipment is likely to come into contact with aggressive substances, it is the
responsibility of the user to take suitable precautions that prevent it from being adversely
affected, thus ensuring that the type of protection is not compromised.

Aggressive substances:e.g. acidic liquids or gases that may attack metals, or solvents
that may affect polymeric materials

Suitable precautions:e.g. regular checks as part of routine inspections or establishing
from the material’s data sheet that it is resistant to specific chemicals

Note:

The metallic alloy used for the enclosure material may be at the accessible surface of
this equipment; in the event of rare accidents, ignition sources due to impact and friction
sparks could occur. This shall be considered when the 2120 is being installed in
locations that specifically require zone 0 equipment.

7. It is the responsibility of the user to ensure:

a. That the joint requirements between the switch and the vessel tank are compatible

with the process media.

b. That the joint tightness is correct for the joint material used.

8. The switch fork is subjected to small vibration stresses as part of its normal function. As

this provides a partition wall, it is recommended that the fork should be inspected every 2
years for signs of defects.

9. It is the responsibility of the user to ensure that only suitably certified cable entry devices

will be utilized when connecting this equipment.

«
...
60
61
62
63
64
...
»

Содержание 2120









































































Отзывы:

Нет отзывов

Похожие инструкции для 2120

Бренд: jenway Страницы: 20

Acuvim-L Series

Бренд: AccuEnergy Страницы: 83

Бренд: Gazelle Страницы: 2

Бренд: Kamstrup Страницы: 100

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 12

Бренд: Kamstrup Страницы: 60

Бренд: Kamstrup Страницы: 136

Бренд: Kamstrup Страницы: 16

Бренд: Kamstrup Страницы: 155

Бренд: Lake Shore Cryotronics Страницы: 97

Dusty Harp Pickup Series

Бренд: Dusty Strings Страницы: 5

Бренд: RADWAG Страницы: 176

Бренд: TA Instruments Страницы: 68

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Micro Alti Vario Plus

Бренд: Fairhaven Страницы: 20

Бренд: Major tech Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды