manualshive.com logo in svg

Rose electronics RP2-1R2X16U, Инструкция по установке и эксплуатации

Поделиться
Скачать
Rose electronics RP2-1R2X16U Скачать руководство пользователя страница 63

 

 

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

  

57 

 

Appendix C – RackMount 

The rack mount kit includes the following items: 

n

  Two black anodized mounting brackets 

n

  Four 6 - 32 x 3/8” flat head mounting screws 

 
To rack mount your UltraMatrix Remote, attach the two rack mounting brackets to yo/ur Unit with the short flange 
against the Unit using the four screws provided. Secure the mounting brackets to the rack using the appropriate size 
bolts, nuts and lock washers. Using hardware other than that provided could cause damage to the electronics and/or 
result in loss of mounting integrity. Do not over tighten the screws used to mount the Unit to the mounting brackets. 
 
The following general guidelines should be observed when installing your Unit into a rack. 
 
a).  The UltraMatrix Remote is designed to work in an ambient temperature of 0

ο

 

C to 45

ο

 

C (32

ο

 

F – 113

ο

 F). 

b).  Do not block power supply vents or otherwise restrict airflow when rack-mounting this Unit. 
c).  Mechanical loading of the rack should be considered to prevent instability and possible tipping over. 
d).  Tighten all connectors securely and provide adequate strain relief for all cables. 
e).  Provide a grounded power source to all Units.  Pay special attention to overall branch circuit load ratings before 

connecting equipment to this source.  Overloaded circuits are potential fire hazards and can cause equipment 
failures or poor performance. 

 
 
 
 

Rack mount illustration 

 

 

 
 
 
 
 

 

 
 
 
 
 

Содержание RP2-1R2X16U





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды