Rose electronics RP2-1R2X16U Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 68

Rose electronics RP2-1R2X16U Скачать руководство пользователя страница 29

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

23

System Status display

Figure 13. System Status display

The system status display is a very powerful and useful tool when installing, monitoring, expanding, troubleshooting,
or reconfiguring a system. The status screen displays reported information from all CPU cards in the system.

Computers

Indicates the CPU port numbers for a given CPU card.
Highlighted computer numbers are the total computer ports in the system.

Power

Each CPU card represents 4 CPU ports. These ports are represented by the four squares. The CPU ports are (Left
square to right square), CPU port 1, port 2, port 3, and port 4. (Green = CPU is on, Red = CPU is off)

Pos (Position)

Displays the slot where a CPU card in the system is installed for a given switch. Slot 1 is the bottom CPU card; slot 2
is the top CPU card for the 2 user model, slot 4 is the top CPU card for the 4 user model.

Ver (Version)

Displays the last three digits of the firmware main program version for the CPU card.

KVM

Indicates the type of keyboard and mouse detected if a KVM station is attached to this CPU card.

CPU

Displays the computer number currently selected by the KVM station.

User

Displays the users name that is currently accessing the system.

Status

Displays the most recent connect or disconnect status for the KVM station on this CPU card.

System Status

Computer Power Pos Ver KVM

CPU User

Status

1-4

1 21C

PC

1 User 1 Share mode

5-8

2 21C

PC

2 User 2 Share mode

9-12

3 21C

PC

3 User 3 Share mode

13-16

4 21C

PC

4 User 4 Share mode

17-20

1 21C

PC

No response

21-24

2 21C

PC

No response

25-28

3 21C

PC

No response

29-32

4 21C

PC

No response

33-36

1 21C

PC

No response

37-40

2 21C

PC

No response

41-44

3 21C

PC

No response

45-48

4 21C

PC

No response

49-52

1 21C

PC

No response

53-56

2 21C

PC

No response

57-60

3 21C

PC

No response

61-64

4 21C

PC

No response

Pos=Card position | Ver=Program version | KVM=PC/Sun/None
CPU power =on =off | Line color

Good

Disconnected

Error

«
...
27
28
29
30
31
...
»

Содержание RP2-1R2X16U





































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды