manualshive.com logo in svg

Rose electronics RP2-1R2X16U, Инструкция по установке и эксплуатации

Поделиться
Скачать
Rose electronics RP2-1R2X16U Скачать руководство пользователя страница 31

Switch Installation 

 

ULTRAMATRIX REMOTE INSTALLATION AND OPERATIONS MANUAL

  

25 

Switch Installation – Single Unit 

 
 

 

The basic installation of a single UltraMatrix Remote is an easy and straightforward procedure. Perform the below 
steps for all computers that will be connected.  It is recommended that all computers be powered off.  When a 
computer is connected and then booted, the UltraMatrix Remote will automatically determine the keyboard and 
mouse types used for that computer and no pre-configuration is needed.   
 
The connection to the network can be done at this time but it is not necessary to install a single unit. 
 

 

The Unit above can be any UltraMatrix Remote model 

 

If removing power from a computer is not practical, pre-configure the UltraMatrix Remote to define that CPU port’s 
keyboard and mouse types.  This procedure should only be done if the CPUs keyboard and mouse can be 
disconnected and re-connected without affecting the interface. 
The default keyboard type is PC mode 2, and the default mouse type is PS/2.  If the computer being connected, with 
power applied, uses a PC2 keyboard and PS/2 mouse, no pre-configuration is needed. If not, pre-configure the 
keyboard and mouse types for that CPU port before connecting the computer (steps 4a-4e).   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Please refer to the safety section before installation 
 

Содержание RP2-1R2X16U





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды