Roland VIMA JM-8 Скачать руководство пользователя страница 93

Страница: 93 / 176

DRUM INSTR EDIT

VIMA JM-8

values by the same amount (leaving variations
intact), while a positive setting shifts all velocity val-
ues in a positive direction.

PITCH:

Use this parameter to tune the selected drum

instrument higher or lower. “0” means that the pitch
is left unchanged.

■

Equalizer

The equalizer on the “DRUM INSTR.” page applies to
the selected drum instrument only. The small “INSTR.
EQUALIZER” display field allows you to select one of
the following options:

Note:

If you hear no difference between “Glbl” and “Off”,

the Drum Set’s equalizer (on the “PALETTE” page) is set to

[OFF]

If you want to take advantage of the drum instru-
ment’s equalizer and edit it to your liking…

(1) Press the

[INSTR.¥EQUALIZER]

display field and use

the dial to select “Instr”.

Note:

Press the

[EDIT]

display button to change the equal-

izer settings. The display changes to:

The name of the currently selected drum instrument
is displayed in the upper left corner. You cannot
select different instruments here.

(The

[EDIT]

display button indicates that you can

change the parameters on this page. It cannot be
switched off.)

(2) Press the display field of the parameter you wish to

change.

(3) Set the desired value with the dial.

You can also press the dial to call up a numeric pad
window. Use the display buttons of that window to
enter the desired values and confirm with the

[ENTER]

display button.

INSTR VOL:

This parameter duplicates the VOLUME

parameter on the “DRUM INSTR. EDIT” page. The rea-
son why it’s also available here is that some equalizer
settings may lead to rather noticeable level drops or
hikes.

INSTR EQ:

This parameter duplicates the little display

in the “INSTR. EQUALIZER” section of the “DRUM
INSTR. EDIT” page. It allows you to make comparisons
and to specify which equalizer (if any) should be
applied to the selected drum instrument. The various
parameter fields (HI FREQ HZ, etc.) always show the
“Instr” settings. They are not updated when you
select “Glbl” (and thus don’t show the Global equal-
izer settings), nor do they disappear when you select
“Off”.

HI FREQ HZ (1500, 2000, 3000, 4000, 6000, 8000,
12000Hz):

This parameter allows you to set the cut-

off frequency of the high band (this is a shelving fil-
ter).

HI GAIN DB (–15~15dB):

Use this parameter to set

the level of the selected HI frequency. Positive values
boost (increase the volume of) that frequency, nega-
tive values cut (attenuate) it.

MID FREQ HZ (200~8000Hz):

This parameter allows

you to set the cutoff frequency of the middle band
(this is a peaking filter).

MID Q (0.5, 1, 2, 4, 8):

Use this parameter to specify

the width of the MID FREQ band that you want to
boost or cut. Smaller values mean that neighboring
frequencies above/below that value are also affected.

MID GAIN DB (–15~15dB):

Use this parameter to

set the level of the selected MID frequency. Positive
values boost (increase the volume of) that frequency,
negative values cut (attenuate) it.

LO FREQ HZ (90, 150, 180, 300, 360, 600Hz):

This

parameter allows you to set the cutoff frequency of
the low band (this is a shelving filter).

LO GAIN DB (–15~15dB):

Use this parameter to set

the level of the selected LO frequency. Positive values
boost (increase the volume of) that frequency, nega-
tive values cut (attenuate) it.

To copy your equalizer settings to other drum instru-
ments, proceed as follows:

(a) Set the EQ parameters to your liking.

(b) Press the