75
Information That You Will Find Useful
■
Flanger
The flanging effect gives a twisting, jet-airplane-like
character to the sound.
■
Flex Band Filter
The flex band filter cuts the high and low frequency
range, and the frequencies for each range are freely
adjustable. This is suitable for making lo-fi sounds
such as radio tone.
■
Lo-Fi Saturator
This produces natural distortion like that obtained
with older audio equipment or an AM radio.
It’s ideal for creating lo-fi sounds.
■
Low Cut Filter
This is a filter that cuts unwanted low range noise,
such as pops.
■
Limiter
The limiter attenuates loud input levels to prevent
distortion.
■
Noise Suppressor
The noise suppressor leaves the original sound
unmodified, but mutes only the noise during the
silent intervals.
■
Phaser
Phaser is an effect that adds a phase-shifted sound to
the direct sound, making the sound more spacious.
■
Pan
Pan cyclically moves the stereo position between left
and right (when stereo output is used).
FL Pre Filter
Select the type of filter.
Off:
a filter will not be used
LPF:
cut the frequency range above the Cutoff parameter
HPF:
cut the frequency range below the Cutoff parameter
FL Cutoff
(cutoff frequency)
Adjusts the frequency where the harmonics contents of the sound
is cut off.
FL Manual
Adjusts the center frequency at which the flanging effect will be
applied.
FL Rate
Adjusts the rate at which flanger is modulated.
FL Depth
Adjusts the depth of modulation for the flanger.
FL Phase
Adjusts the spatial spread of the sound.
FL Resonance
Determines the amount of resonance (feedback). Increasing the
value will emphasize the effect, creating a more unusual sound.
FL Balance
Adjust the balance between the effect sound volume and the
direct sound volume.
FL Level
Adjusts the volume.
BF Sw (switch)
Turns the flex band filter effect on/off.
BF High Cut
Adjusts the frequency above which the flex band filter cut the
high frequency range.
BF Low Cut
Adjusts the frequency below which the flex band filter cut the
low frequency range.
BF Level
Adjusts the volume.
ST Sw (switch)
Turns the lo-fi saturator effect on/off.
ST Drive
This parameter adjusts the amount of distortion.
ST Color
Adjusts the sound brilliance. Smaller values produce a
rougher sound, and larger values produce a clearer sound.
ST Level
Adjusts the volume.
LC Sw (switch)
Turns the low cut filter effect on/off.
LC Low Cut
Adjusts the frequency at which the low cut filter will begin to
take effect.
LM Sw (switch)
Turns the limiter effect on/off.
LM Threshold
Adjust this as appropriate for the input signal from your
guitar. When the input signal level exceeds this threshold
level, limiting will be applied.
LM Release
This adjusts the time from when the signal level drops below
the threshold until when limiting is removed.
LM Post Gain
Adjusts the output gain.
LM Level
Adjusts the volume.
NS Sw (switch)
Turns the noise suppressor effect on/off.
NS Threshold
Adjusts the level at which the noise suppressor will begin to take
effect. When the signal drops below the specified level, it will be
muted.
PH Sw (switch)
Turns the phaser effect on/off.
PH Manual
Adjust the center frequency at which the phaser effect will apply.
PH Rate
Adjust the rate at which the phaser will modulate.
PH Depth
Adjust the depth of the phaser effect.
PH Phase
Adjusts the spatial spread of the sound.
PH Resonance
Adjust the amount of resonance. Raising this value will produce a
more distinctive tone.
PH Balance
Adjust the balance between the effect sound volume and the
direct sound volume.
PH Level
Adjusts the volume.
PN Waveform
Select the type of modulation.
Tri:
The sound will be modulated like a triangle wave.
Sqr:
The sound will be modulated like a square wave.
Sin:
The sound will be modulated like a sine wave.
Saw1, 2:
The sound will be modulated like a sawtooth wave.
* The [teeth] in Saw1 and Saw2 point at opposite direction.
PN Rate
Adjusts the frequency (speed) of the change.
PN Depth
Adjusts the depth of the effect.
PN Level
Adjusts the volume.
