27
B
A
C
Frame types
The
requires a frame spacing of 135mm, all frames with different frame spacing or for
thru axles are not suitable for the
The inner side of the left hand dropout must be flat in a
diameter of 40mm around the center of the axle so that the axle plate can sit firmly and evenly against the dropout.
There are different
versions available (for the different dropout types) with the suitable
axle and axle plate along with the corresponding parts for mounting. The
does not
include a brake. To mount a brake (disc or rim), the frame must have the correct brake mounts.
Rohloff SPEEDHUB 500/14
Rohloff SPEEDHUB 500/14.
Rohloff SPEEDHUB 500/14
Rohloff SPEEDHUB 500/14
Frame types for the long torque arm:
When the slot lenght is longer than 25mm ( ), a chain tensioner does not
have to be used as there is enough adjustment room within the slot to
tension the chain.
The following versions of the
are, therefore,
suitable:
TS
TS EX
B
Rohloff SPEEDHUB 500/14
On frames with vertical dropout slots ( ) the mounting of the
normally suggests a CC quick release version (CC or
CC EX). This as opposed to the TS versions (TS and TS EX) allows for a
quicker wheel removal/installation without the use for tools.
The following versions of the
, therefore,
suitable:
CC
CC EX
TS*
TS EX*
C
Rohloff
SPEEDHUB 500/14
Rohloff SPEEDHUB 500/14 are
On frames with horizontal dropout slots, it is only possible to mount the
in the TS threaded axle versions (TS and TS
EX). The CC versions with a quick release lever will not hold the wheel
secure enough and the wheel could be pulled crooked whilst riding.
When the slot lenght is shorter than 25mm ( ), a chain tensioner (Art.
#8250) must be fitted as there is not enough adjustment room within the
slot to tension the chain.
The following versions of the
are, therefore,
suitable:
TS*
TS EX*
Rohloff SPEEDHUB 500/14
Rohloff SPEEDHUB 500/14
A
* These versions must be used in conjunction with a chain tensioner (Art.No. 8250) except when an eccentric BB
is being used.. The chain tensioner should be ordered with the initial product as it is not to be found in the regular
package.
Securing to the frame
Slot length
shorter than 25mm
Slot length
larger than 25mm
!
28
E
SPEEDBONE
SPEEDBONE
D
MonkeyBone
MonkeyBone
On frame types ( ) with a Horst Link, the mounting is only
possible with the use of the OEM2 axleplate.
All
versions can be mounted on
this frame type, the only accessory needed is the OEM2
axleplate.
Horst Link, named after his inventor Horst Leitner.
E
Rohloff SPEEDHUB 500/14
When mounting the hub with the use of the OEM2 axle plate, the disc brake mounts will be used to secure the torque
of the hub. Therefore, permission must be obtained from the frame manufacturer to ensure that the guarantee is not
affected. The mounting instructions for the OEM2 usage must be read carefully (see "Mounting instructions for
OEM2").
Frame types for OEM2 mounting
For frames with vertical dropouts and international standard disc brake mounts (IS 1999), the use of an OEM2
axleplate is highly recommended. With this, the disc brake mount will be used to secure the torque of the hub. Two
mounting possibilities are to be decided between:
1) Mounting with a disc brake on the rear wheel
The torque is secured through the
(Art. #8550),
(160mm= Art. #8553/
180mm=Art. #8554), then through the disc brake mounts and secured tightly into the brake disc caliper.
2) Mounting without a disc brake on the rear wheel
The
is not necessary. A support bolt secured through the lower disc brake
mount can be used to support the torque.
Rohloff SPEEDBONE
MonkeyBone
Rohloff SPEEDBONE/MonkeyBone
On frames ( ) with international disc brake mounts (IS
1999), the OEM2 mounting is recommended. As an
alternative the long torque arm could also be used (see frame
type ).
All
versions can be mounted on
this frame type, the only accessory needed is the OEM2
axleplate.
D
C
Rohloff SPEEDHUB 500/14
When mounting on Tandems even without the use of a disc brake, the
must be
mounted and its supporting peg used to support the torque of the OEM2 axleplate. A chain tensioner must also be
mounted in conjunction with the use of the OEM2 mounting, except on frames built around an eccentric BB system.
Rohloff SPEEDBONE/Monkey Bone
A T T E N T I O N
Securing to the frame
Horst Link
A T T E N T I O N
