manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 33

Command Reference

R&S

®

CMW-KM645

33

User Manual 1173.9740.02 ─ 04

See also: "Retrieving Measurement Results" in the R&S

 

CMW user manual, chapter

"Remote Control"

6.1.3 Current and Statistical Results

The R&S

 

CMW repeats measurements according to the selected statistic count and

repetition mode. Consecutive measurement values are stored and used to calculate
statistical results, e.g. average, minimum, maximum and standard deviation.

See also: "Statistical Results" in the R&S

 

CMW user manual, chapter "System Over-

view"

6.1.4 Values for RF Path Selection

To select an RF input path, you must specify an RF connector and an RX module (con-
verter).

Which connectors and modules can be specified in a command, depends on the instal-
led hardware, the test setup and the active sub-instrument or instance <i>.

This section lists all values available for path selection. Depending on your configura-
tion, only a subset is relevant for you. Virtual connector names are only relevant for
setting commands. Queries return the physical connector names.

Additional information is available in the base software documentation. It describes typ-
ical instrument configurations with the allowed RF connector - TX/RX module combina-
tions and the mapping of virtual connector names to physical connectors.

See also: "Signal Path Settings" in the R&S

 

CMW user manual, chapter "Remote Con-

trol"

Single R&S CMW

RF path selection values:

●

RX module:

RX1 | RX2 | RX3 | RX4

●

RX connector:

RF1C | RF2C | RF3C | RF4C | RFAC | RFBC

RF 1 COM to RF 4 COM plus virtual connector names

One R&S CMW plus one R&S

 

CMWS

RF path selection values:

●

RX module:

RX1 | RX2 | RX3 | RX4

●

RX connector:

R11 | R12 | R13 | R14 | R15 | R16 | R17 | R18
R21 | R22 | R23 | R24 | R25 | R26 | R27 | R28
R31 | R32 | R33 | R34 | R35 | R36 | R37 | R38
RA1 | RA2 | RA3 | RA4 | RA5 | RA6 | RA7 | RA8

 

 

Conventions and General Information

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды