manualshive.com logo in svg

Rohde & Schwarz CMW-KM645, Руководство пользователя

Поделиться
Скачать
Rohde & Schwarz CMW-KM645 Скачать руководство пользователя страница 18

General Description

R&S

®

CMW-KM645

18

User Manual 1173.9740.02 ─ 04

The statistical values in the tables are calculated as follows:

●

Current:

 Value of the result obtained in the last measurement interval.

●

Average:

 Average of all "Current" values referenced to the last statistics cycle.

●

Max:

 Largest "Current" value that the R&S

 

CMW obtained since the start of the

measurement.

●

Min:

 Smallest "Current" value that the R&S

 

CMW obtained since the start of the

measurement.

●

StdDev:

 Standard deviation of all "Current" values since the start of the measure-

ment.

All statistical results (statistical tables and "Average" or "Max" traces) are calculated
according to the general rules for statistical results.

See also: "Statistical Results" in the R&S

 

CMW user manual, chapter "System Over-

view"

Statistic Count

Progress bar for the measurement, displayed in all detailed views. During the first sin-
gle shot after the start of the measurement, the bar shows the number of elapsed mea-
surement intervals relative to the "Statistic Count". A filled progress bar indicates that
the first shot is complete and the statistical depth has been reached.

See also: "Statistical Settings" in the R&S

 

CMW user manual, chapter "System Over-

view"

Out of Tolerance

Percentage of measurements that were failed because they exceeded the specified
limits.

Measurement Results

深圳德标仪器 

135-1095-0799

Содержание CMW-KM645


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды