Roger PRT12 v1.3 Скачать руководство пользователя страница 24

Страница: 24 / 40

PRT12 v1.3 fv75.6 EN Rev.D.doc

10/22/2007

_________________________________________________________________________________________

Page 24 of 40

Acoustic and optical signals in Offline mode

Acoustic Signals in Offline (stand-alone) mode

Signal

Symbol

Description

One long signal

Error - unknown identifier, access denied.

Two long signals

- -

Attempt to assign the same function for two different
input lines.

Three short beeps

* * *

Command successfully completed (OK signal).

Two short beeps

* *

Prompt signal, the reader is waiting for the next part of
the command to be entered. This signal is intended to
encourage the programmer to proceed with next
programming steps.

One long signal
continuously
repeated

- - - - - -

… and

so on

Memory contents corrupted or either MASTER or
INSTALLER card not programmed -

Memory Reset

necessary. This signal is accompanied by the steady lit
LED SYSTEM .

Legend:

single long audible signal,

single short audible signal (beep)

LED Indications in Offline (Stand-alone) mode

LED

STATUS

LED

OPEN

LED

SYSTEM

Description

Green

—

The reader is in Disarmed state now.

Red

—

The reader is in Armed state now.

Red

Green

—

The reader is in

User Programming

mode.

Green

—

The reader is in

Installer Programming

mode.

—

Orange

Flashing

Waiting for the user to enter the next part of the command or
programming function.

—

Orange,

(single

flash)

A user identifier (Card/PIN) has been entered.

—

Green

—

The door lock is activated, this LED remains ON as long as a door
is unlocked.

—

Green

flashing

—

The reader is waiting for a user to enter his identifier once again.

—

Steady

The reader has detected some problem (memory contents is
corrupted or the MASTER & INSTALLER cards are not
programmed).

Содержание PRT12 v1.3









































Результаты поиска

Содержание PRT12 v1.3

Отзывы:

Похожие инструкции для PRT12 v1.3

Бренды по названию

Популярные бренды

Roger PRT12 v1.3, Инструкция по установке и программированию

Результаты поиска

Содержание PRT12 v1.3

Отзывы:

Похожие инструкции для PRT12 v1.3

Бренды по названию

Популярные бренды