background image

S-8600 UHF RFID Reader User Manual 

UHF RFID User Manual 

26 

3. Develop your own RFID Application 

You can operate most functions of reader through the demo. But in actual situation, may 

be you need to develop your own applications. 

Supplied  document: 

UHF  RFID  serial  interface  protocol_V2.38.pdf

  provides  a 

complete interface to operate reader. 

This  port  is  based  on  serial  communication,  so  both  RS  -  232  and  TCP  /  IP,  the  reader 

follows the definition of the interface. 

Demo  provides  an  important  function:  recording  serial  transmission,  users  can  quickly 

grasp the content of Communication protocol document when you compared it with serial 

data in the actual operation. 

Select  the  checkbox  of

  Activate  Serial  Port  Monitor

  on  the  bottom  right  corner,  all 

uplink and downlink serial data will be recorded, as illustrated below: 

 

Note: Response speed of Demo will be slow down after opening the 

Activate Serial Port 

Monitor

. Generally, this function should be turn off. 

Violet blue information is sent to reader by PC, red information is back to PC via reader. 

Input  Command

  manually  used  to  debug  serial  command  which  could  calculate 

checksum automatically. 

In  addition,  the  supplied  documentation  also  includes  the  complete  source  code  of  the 

demo

Based on C # of .Net platform

. To help users develop applications based on this 

reader. 

During the development process, users could refer to the documentation "Developer FAQ 

Q & A.PDF" or contact our Technical Support Engineer. 

Содержание S-8600



























Отзывы: