background image

S-8600 UHF RFID Reader User Manual 

UHF RFID User Manual 

23 

2.6 Other Settings 

 

2.6.1 Set DRM Status 

 

DRM is Dense Reader Mode. When multiple readers work at the same time, the RF signal 

transmission  will  interfere  with  each  other,  you  can  open  the  DRM  mode  to  reduce  the 

interference between them. 

Operation interface as below (Reader Setup->RF Setup): 

         

 

Note: If DRM was opened, the sensitivity of the reader will reduce significantly. So users 

could start this function according to the actual situation.   

   

2.6.2 Operating Temperature Monitoring 

 

Reader will generate heat under high intensity continuous working. Users can monitor the 

internal  temperature  via  the  built-in  temperature  sensor  to  avoid  reader  overheating 

(Operating temperature over 65

). If it’s too hot, you could stop reading for a while. 

 

Interface of the 

Temperature Monitor

 as below: 

 

 

2.6.3

 

Set GPIO Level 

 

General-purpose  input/output  (GPIO)  is  a  generic  pin  on  an  integrated  circuit  whose 

behavior (including whether it is an input or output pin) can be controlled (programmed) 

by the user at run time. This reader provides two opto-isolated inputs (GPIO1 and GPIO2) 

and two opto-isolated outputs (GPIO3 and GPIO4). 

 

The image of GPIO port with connector as below: 

Содержание S-8600



























Отзывы: