manualshive.com logo in svg

Rockwell Automation 440R-D22R2, Руководство пользователя

Поделиться
Скачать
Rockwell Automation 440R-D22R2 Скачать руководство пользователя страница 70

70

Rockwell Automation Publication 440R-UM013F-EN-P - July 2021

Chapter 11          Troubleshooting

Check the PowerFlex Drive Connections

Confirm that voltage is present at the relay terminals and the safety input 
terminals of the PowerFlex drive. 

Figure 79

 shows an example of the 

measurement points for one output channel (terminal 34). Repeat the checking 
on the second channel (terminal 44). The terminal connections from 34 and 44 
to S1 and S2 can be reversed.

Figure 79 - Typical Connections to PowerFlex Drive

Figure 80 on page 71

 shows the test connections to verify the common 

reference between the DIS safety relay and the AC Drive. Remove power from 
the application and set the digital multimeter to ohms. If possible, measure 
directly at the terminals. The resistance must be less than 1 ohm.

Step

Description

1

The voltage at 14 must be slightly less than the supply voltage. If not, then the DIS safety relay must be 
replaced.

2

The voltage at A1 must be slightly less than the supply voltage and must be the same voltage as 
measured at terminal 14. If not, check for an open circuit (broken wire) between terminal 14 and A1.

3

The voltage at A2 must be zero. If not, check for an open circuit between A1 and the voltage supply 
ground connection. If A2 measures zero volts and A1 measures the supply voltage, then K1 is not 
operating properly, and must be replaced.

Step

Description

1

The voltage at 34 must be slightly less than the supply voltage. If not, then the DIS safety relay must be 
replaced.

2

The voltage at S2 must be slightly less than the supply voltage and must be the same as the voltage at 
terminal 34. If not, check for an open circuit (broken wire) between terminal 34 and S2.

3

The voltage at terminal 4 must be zero. If not, check for an open circuit between terminal 4 and the 
voltage supply ground connection. 

Figure 80 on page 71

 shows how to verify the continuity from 

terminal 4 of the drive to terminal A2 of the DIS safety relay.

SHOCK HAZARD: 

Turn power OFF before continuity is tested.

34 44 14  24 

S2 

4 

S1 

A1

A2

23

Volts

DMM

1

2

3

OUT

24V common

24V DC supply

PowerFlex 525

AC Drive

Motor

Содержание 440R-D22R2



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды