manualshive.com logo in svg

Rockwell Automation 440R-D22R2, Руководство пользователя

Поделиться
Скачать
Rockwell Automation 440R-D22R2 Скачать руководство пользователя страница 31

Rockwell Automation Publication 440R-UM013F-EN-P - July 2021

31

Chapter

 4

Configuration

The multi-position, rotary switches on the front face of a GSR safety relay 
determine its functionality. The configuration method of a GSR safety relay 
must provide means to help protect against manipulation and maintain 
integrity of the configuration.

The rotary switches accommodate a small screwdriver to turn the switch to the 
desired switch position. The configuration procedure implies a willing action 
by the person who configures the safety function to prove that the person is 
conscious and able to perform this task. Therefore, GSR safety relays require a 
procedure of turning a switch to position “0” to start the configuration mode 
and then turn to the position desired.

The status indicators on the front panel provide continuous feedback by 
flashing the switch positions. Power cycling the device in a timely manner 
completes the configuration mode and the device enters operation.

We recommend that the configuration is completed within 5 minutes. The 
actual technical limitation of the internal EEPROM is around 8 hours. The 
internal micro-controllers monitor and verify the switch positions during 
configuration to achieve the required diagnostics coverage for the PLe safety 
rating. The EEPROM read/write cycles are limited and can cause a permanent 
fault of the GSR safety relay after several hours.

Switch Adjustment

These safety relays have multi-position switches on their front face. Use a 
small screwdriver to set the switches to the desired setting.

Figure 25 - Configuration Switch Adjustment

IMPORTANT

To keep your GSR safety relay from permanently faulting, complete the 
configuration process by power cycling the relay within 5 minutes after 
configuring rotary switches.

Make note of the mechanical stop location.

IMPORTANT

Adjust the switches gently and do not turn past the mechanical stops.

0

Mechanical 

Stops

Screwdriver 

Slot

Содержание 440R-D22R2



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды