Robotis DYNAMIXEL XM430-W210 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 34

background image

2/22/2018

ROBOTIS e-Manual

http://emanual.robotis.com/docs/en/dxl/x/xm430-w210/

22/34

packet. If the value of Bus Watchdog (98) is changed to ‘0’,
Bus Watchdog Error will be cleared.

Note

For details of Range Error, please refer to the protocol of

the e-Manual.

The following are examples of the operation of the Bus
Watchdog function.

1. After setting the operating mode (11) to speed control

mode, change the Torque Enable (64) to ‘1’.

2. If ‘50’ is written in the Goal Velocity (104), the DYNAMIXEL

will rotate in CCW direction.

3. Change the value of Bus Watchdog (98) to ‘100’ (2,000

[ms]). (Activate Bus Watchdog Function)

4. If no instruction packet is received for 2,000 [ms], the

DYNAMIXEL will stop. When it stops, the Profile
Acceleration (108) and Profile Velocity (112) are applied as
‘0’.

5. The value of Bus Watchdog (98) changes to ‘-1’ (Bus

Watchdog Error). At this time, the access to the Goal Value
will be changed to read-only.

6. If ‘150’ is written to the Goal Velocity (104), Range Error will

be returned via Status Packet.

7. If the value of Bus Watchdog (98) is changed to ‘0’, Bus

Watchdog Error will be cleared.

8. If “150” is written in the Goal Velocity (104), the

DYNAMIXEL will rotate in CCW direction.

2. 4. 28. Goal PWM(100)

In case of PWM Control Mode, both PID controller and
Feedforward controller are deactivated while Goal PWM(100)
value is directly controlling the motor through an Inverter. In
other control modes, this value is used to limit PWM value.
This value cannot exceed PWM Limit(36). Please refer to the
Gain section in order to see how Goal PWM(100) affects to
different control modes.

Range

Description

-PWM Limit(36) ~ PWM Limit(36) Initial Value of PWM Limit(36) : ‘885’

2. 4. 29. Goal Current(102)

In case of Torque Control Mode, Goal Current(102) can be
used to set a target current. This value sets a limit to current in
Current-based Position Control mode. This value cannot
exceed Current Limit(38).

Back to Top ▲

«
...
20
21
22
23
24
...
»

Содержание DYNAMIXEL XM430-W210



































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMIXEL XM430-W210

Бренд: ABB Страницы: 6

Бренд: Falcon Страницы: 52

Бренд: KaVo Страницы: 16

Бренд: Bahco Страницы: 9

Бренд: Banfer Страницы: 6

Бренд: Bang & Olufsen Страницы: 2

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Federal Страницы: 43

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: FabiaTech Страницы: 2

Бренд: FabiaTech Страницы: 77

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: Waterpik Страницы: 2

Бренд: RAMVAC Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды