Robotis DYNAMIXEL XM430-W210 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 34

background image

2/22/2018

ROBOTIS e-Manual

http://emanual.robotis.com/docs/en/dxl/x/xm430-w210/

15/34

Unit

Value Range

0.088° 0 ~ 4,095(1 rotation)

Note

Max Position Limit(48) and Min Position Limit(52) are only

used in Position Control Mode with a single turn.

2. 4. 19. Shutdown(63)

The Dynamixel can protect itself by detecting dangerous
situations that could occur during the operation.
Each Bit is inclusively processed with the ‘OR’ logic, therefore,
multiple options can be generated.
For instance, when ‘0x05’ (binary : 00000101) is defined as
Shutdown(63), Dynamixel can detect both Input Voltage
Error(binary : 00000001) and Overheating Error(binary :
00000100).
If those errors are detected, Torque Enable(64) is cleared to ‘0’
and the motor output becomes 0[%].
REBOOT is the only method to reset Torque Enable(64) to
‘1’(Torque ON) after the shutdown.
The followings are detectable situations.

Bit

Item

Description

Bit

7

-

Unused, Always ‘0’

Bit

6

-

Unused, Always ‘0’

Bit

5

Overload

Error(default)

Detect persistent load that exceeds maximum
output

Bit

4

Electrical Shock

Error(default)

Detect electric shock on the circuit or
insufficient power to operate the motor

Bit

3

Motor Encoder

Error

Detect malfunction of the motor encoder

Bit

2

OverHeating

Error(default)

Detect internal temperature exceeds the
configured operating temperature

Bit

1

-

Unused, Always ‘0’

Bit

0

Input Voltage

Error

Detect input voltage exceeds the configured
operating voltage

Note

If Shutdown occurs, use below method to reboot

Dynamixels.

1. H/W REBOOT : Turn off the power and turn on again
2. S/W REBOOT : Transmit REBOOT Instruction (For more

details, please refer to the [Reboot] section of Protocol e-

Back to Top ▲

«
...
13
14
15
16
17
...
»

Содержание DYNAMIXEL XM430-W210



































Отзывы:

Нет отзывов

Похожие инструкции для DYNAMIXEL XM430-W210

Бренд: GBC Страницы: 8

Бренд: KAPSCH Страницы: 57

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: Farmet Страницы: 102

Бренд: Yamaha Страницы: 46

univers N UC21LH1

Бренд: hager Страницы: 13

univers N UK31LH1FM

Бренд: hager Страницы: 2

univers N UK21LH1M

Бренд: hager Страницы: 3

Бренд: v.link Страницы: 20

Бренд: BCP Страницы: 8

APPLETON EBR 30 Series

Бренд: EGS Страницы: 2

Бренд: Lutron Electronics Страницы: 10

Бренд: Mikrona Страницы: 12

Бренд: Mark Fitness Страницы: 10

Z62-M450.01 S21

Бренд: Jäger Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды