Robotis Dynamixel X Series Скачать руководство пользователя страница 19

Страница: 19 / 34

Therefore, when a new value is written to the Goal Value, a Range Error will be returned via the
Status packet. If the value of

Bus Watchdog(98)

is changed to ‘0’, Bus Watchdog Error will be

cleared.

NOTE

: For details of Range Error, please refer to the protocol of the e-Manual.

The following are examples of the operation of the Bus Watchdog function.

1. After setting the

Operating Mode(11)

to speed control mode, change the

Torque Enable(64)

to ‘1’.

2. If ‘50’ is written in the

Goal Velocity(104)

, the DYNAMIXEL will rotate in CCW direction.

3. Change the value of

Bus Watchdog(98)

to ‘100’ (2,000 [ms]). (Activate Bus Watchdog

Function)

4. If no instruction packet is received for 2,000 [ms], the DYNAMIXEL will stop. When it stops,

the

Profile Acceleration(108)

and

Profile Velocity(112)

are applied as ‘0’.

5. The value of

Bus Watchdog(98)

changes to ‘-1’ (Bus Watchdog Error). At this time, the

access to the Goal Value will be changed to read-only.

6. If ‘150’ is written to the

Goal Velocity(104)

, Range Error will be returned via Status Packet.

7. If the value of

Bus Watchdog(98)

is changed to ‘0’, Bus Watchdog Error will be cleared.

8. If “150” is written in the

Goal Velocity(104)

, the DYNAMIXEL will rotate in CCW direction.

2. 4. 26. Goal PWM(100)

In case of PWM Control Mode, both PID controller and Feedforward controller are deactivated
while

Goal PWM(100)

value is directly controlling the motor through an Inverter. In other control

modes, this value is used to limit PWM value. This value cannot exceed

PWM Limit(36)

. Please

refer to the Gain section in order to see how

Goal PWM(100)

affects to different control modes.

Range

Description

PWM Limit(36)

Initial Value of

PWM Limit(36)

: ‘885’

2. 4. 27. Goal Velocity(104)

In case of Velocity Control Mode, Goal Velocity(104) can be used to set a desired velocity. This
value cannot exceed Velocity Limit(44). For now, Goal Velocity(104) is used for desired velocity,
but this value is not used to limit the velocity.

Unit

Value Range

0.229 rpm -Velocity Limit(44) ~ Velocity Limit(44)

NOTE

: The maximum velocity and maximum torque of DYNAMIXEL is affected by supplying voltage.

Therefore, if supplying voltage changes, so does the maximum velocity. This manual complies with
recommended supply voltage(12[V]).

NOTE

: If

Profile Acceleration(108)

and Goal Velocity(104) are modified simultaneously, modified

Profile Acceleration(108)

will be used to process Goal Velocity(104).

Содержание Dynamixel X Series



































Результаты поиска

Содержание Dynamixel X Series

Отзывы:

Похожие инструкции для Dynamixel X Series

Бренды по названию

Популярные бренды

Robotis Dynamixel X Series, Руководство пользователя

Результаты поиска

Содержание Dynamixel X Series

Отзывы:

Похожие инструкции для Dynamixel X Series

Бренды по названию

Популярные бренды