Roberts Gorden CorayVac Classic SF Series, Руководство по эксплуатации и обслуживанию

Страница: 10 / 94

CRVSF-S
ERIES
I
NSTALLATION
, O
PERATION AND
S
ERVICE
M
ANUAL
4 of 83
SECTION 2: INSTALLER RESPONSIBILITY
The installer is responsible for the follo w ing:
• To ens u re the system is designed in accordance
w ith the parameters of the CRVSF-Series Design
Man u al (P/N 127502NA).
• To pro v ide sched u le 40 heat exchanger radiant
pipe and fittings. Pipe: ASTM A53 (Latest edition)
grade B ERW black steel pipe TNC 4", both ends
threaded to 4" NPT conforming to ANSI/ASME
B1.20.1 (latest edition). Fittings: 150 lb malleable
black iron 4", both ends threaded to 4" NPT
conforming to ANSI/ASME B1.20.1 (latest
edition).
• To install the heater, as w ell as the gas and
electrical s u pplies, in accordance w ith applicable
specifications and codes. Roberts-Gordon LLC
recommends the installer contact a local b
u ilding
Inspector or fire marshal for g u idance.
• To install all threaded components w ith a
minim u m thread engagement of three threads.
Apply s u fficient amo u nt of high temperat u re, anti-
seize pipe compo u nd (P/N 91308001 or
eq u i v alent) to threads prior to engagement. Hot
compo u nd may drip from threads. Protect
s u rfaces u nderneath heater d u ring first start- u p.
• To u se the information gi v en in a layo u t dra w ing
and in the man u al together w ith the cited codes
and reg u lations to perform the installation.
• To install the heater in accordance w ith the
clearances to comb u stibles.
• To f u rnish all needed materials not f u rnished as
standard eq u ipment.
• To plan location of s u pports.
• To pro v ide access to b u rners on all sides for
ser v icing or b u rner remo v al.
• To pro v ide the o w ner w ith a copy of this
Installation, Operation and Ser v ice Man u al.
• To ne v er u se heater as a s u pport for ladder or
other access eq u ipment and to ne v er hang or
s u spend anything from heater.
• To ens u re there is adeq u ate air circ u lation aro u nd
the heater and to s u pply air for comb u stion,
v entilation and distrib u tion in accordance w ith
local codes.
• To safely and adeq u ately install heater u sing
materials w ith a minimal w orking load of 750 lb
(340 kg).
• To ens u re the heater is placed in an appro v ed
application.
• Expansion and contraction of the t u be dictates
that the minim u m s u spension lengths m u st be
maintained. See table on Page 18, Figure 14 .
• To install all components of the system w ith a
minim u m of 18" (45 cm) ceiling clearance in
accordance to National Fire Protection
Association NFPA 30A 7.6.6 (2012 edition) latest
re
v ision.
• To install the o u tside air s u pply system to each
b u rner and end v ent.
• To coordinate w ith ROBERTS GORDON ®
independent distrib u tor the ret u rn of the
completed CORAYVAC ® CLASSIC SF start u p
and installation report w ithin 24 ho u rs of start- u p.
See Page 79, Section 24 .
2.1 Wall Ta g
A laminated w all tag is a v ailable for the heater as a
permanent reminder of the safety instr u ctions and
the importance of the req u ired clearances to
comb u stibles. Please contact Roberts-Gordon LLC
or yo u r ROBERTS GORDON
®
independent
distrib u tor to obtain the w all tag. Affix the tag by
peeling off the backing of the adhesi v e strips on the
rear s u rface and position the tag on a w all near the
CRVSF-Series heater (e.g. thermostat or controller).
A copy of the
w all tag (P/N 91037912) is ill u strated on
the back co v er. For an immediate sol u tion, yo u may
affix this copy on the w all near the heater.
Kno w yo u r model n u mber and installed config u ration.
Model n u mber and installed config u ration are fo u nd
on the b u rner and in the Installation, Operation and
Ser v ice Man u al. See Page 6, Figure 3 . Write the
proper clearance dimensions in permanent ink
according to yo
u r model n u mber and config u ration in
the open spaces on the tag.
2.2 Corrosive Chemicals
Roberts-Gordon LLC cannot be responsible for
ens
u ring that all appropriate safety meas u res are
u ndertaken prior to installation; this is entirely the
responsibility of the installer. It is essential that the
contractor, the s
u b-contractor, or the o w ner identifies
the presence of comb u stible materials, corrosi v e
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.