Robe ColorSpot 575E AT, Руководство пользователя

Страница: 29 / 39

29
9.3 Personality
Use this menu to to modify ColorSpot 575E AT operating behavior.
User mode --- ColorSpot 575E AT allows you to recall up to 3 user settings.After switching the fixture on for the
first time, the User A settings are active.All changes made in "Personality" menu ,"Fixture Address" menu and
Music Trigger and Presetting Playback functions from "Stand-alone setting" menu are saved to the User A settings .If
you now set the User B settings active,from this moment these changes are saved to the User B settings. After
switching the fixture off and on ,the User B setting is active.In this way you may use 3 fixture operating behaviour.
User A Settings --- The function recall the user A settings.
User B Settings --- The function recall the user B settings.
User C Settings --- The function recall the user C settings.
Pan Reverse --- Select this function to invert the pan movement.
Tilt Reverse --- Select this function to invert the tilt movement.
DMX Preseting --- Select this function to set desired effects assigning to the channels.Please refer to the chapter
"DMX protocol" for detail description.
Please refer to the chapter "DMX- protocol" for detail description.
Lamp Presetting --- Select this menu to change the lamp "behaviour".
Lamp On/Power On --- Select this function to turn the lamp on automatically after switching the
fixture on.
Lamp Off via DMX --- Select this function to switch off the lamp via DMX.
Lamp On if DMX Present --- This function allows you to strike the lamp automatically after 26
seconds if DMX signal is present on the data link.If the ignition is unsuccessfull (e.g.lamp is too
hot),the fixture will try to ignite the lamp after next 26 s.This process will repeat until the lamp lights.
Lamp Off if not DMX --- This function allows you to switch Off the lamp automatically after 2
minutes if DMX signal is missing on the data link.
Lamp Ignition Delay --- This function allows you to set the time delay( 0-90s) before the lamp will
be ignited.This setting will not affect starting the lamp direct from the control panel(menu "Lamp On/
Off").
Lamp Light Sensor --- Select this function to switch the lamp light sensor on or off.The option"On" is for the
standard operation.
Important:
The option"Off" is for "emergency operation" only if the lamp light sensor is defective and you will wait
for a service intervertion! If the lamp light sensor is switched off and at switching the lamp on the electronics will
still try to ignite the lamp until it shines (even when the lamp is damaged or absent), on this account some
electronics parts could be damaged!
Display Adjusting --- This function allows you to change the display settings.
Display Permanent On --- This function allows you to keep the display on or to turn off automatically
2 minutes after last pressing any button(or a wheel movement) on the control panel.
Display Intensity --- Select this function to adjust the display intensity (1-min.,10-max.).
Display Backlight --- Select this function to adjust the display backlight (1-min.,10-max.).
Display Turned --- Select this function to turn the display by 180°. You can also turn the the display
by pressing the [ESC] button while the ROBE logo is displayed.
Blackout d.M.C. --- Select this function to enable the blackout during the head movement correction (if the
moving head lost its right pan/tilt position for a short moment) .
Pan/Tilt Feedback --- This function allows to return the mowing head to the required pan/tilt position after changing
the position by external force (e.g.by stroke).
Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the fixture can be
demaged!
Note: If the feedback was switched off ,the pan/tilt-position is changed by an external force and the feedback is
switched on again,the moving head might not to be synchronized with the DMX signal.You have to make a reset
in order to synchronize the moving head with the DMX signal.
Microphone Sensitivity --- Select this function to adjust the microphone sensitivity from 1(maximum) to
20(minimum).If the sensitivity is correctly adjusted,the mark will appear (blinking in the bass beat.)