manualshive.com logo in svg

Robe ColorMix Wash I50, Руководство пользователя, Страница: 8 / 37

Поделиться
Скачать
Robe ColorMix Wash I50 Скачать руководство пользователя страница 8

8

The RECESSED  WASH 150 includes a moving head and a ceiling box for mounting to the lower ceiling.
Installation:
1.Fix the recessed ceiling box (8) to the lower ceiling. Be careful the mounting grid can hold the moving head
installation!
The ceiling box must be fixed properly ,otherwise the vibration of the mounting structure can occur during the
operation of the moving head.Pull the power cable and data cables through the apertures (1) on the bottom of the
box.

2.Put the moving head base (4) on the 4 fixative pins (6) in the bottom of the ceiling box (8) and turn the base
gently to the right. Insert and tighten clockwise the 2 quick-lock fasteners (7) to secure the moving head in the
ceiling box.

3.Use the 3-wired power cable (the wires with cross-sectional area of 1.5mm

2  

) to connect the power.

Verify that the voltage and frequency settings match the local AC supply.The settings are printed on the label  on
the bottom of the moving head base.If you wish to change the power supply settings,see the chapter Appendix.
Pull the power cable through a cable holder (3) and connect it into the connection terminals (2) as follows:

Possible pin identification schemes:

Cable (EU)

  Cable (US)

    Pin

      International

Brown

Black

    Live

     L

Light blue

White

    Neutral

     N

Yellow/Green

Green

    Earth

Содержание ColorMix Wash I50






































Отзывы:

Нет отзывов