Operating Instructions
Roxxy BL-Control 900 series
13
6.15 Max. RPM & Average RPM
This mode shows you the maximum and average rotational speeds
recorded during the last flight, taking into account the values set
under Points 6.14 and 6.15.
6.16 Down Load
Download mode is used for writing (transferring) set values to the
speed controller. Press the INC button to start the process, and the
Programmer then beeps once every second until the procedure is
complete. If you wish to interrupt the process, simply press the
DEC button.
6.17 Restore Memory
Restore Memory is used to access values which have been stored
in the Programmer’s own memory. Press the INC button to start the
process, and the Programmer then beeps once every second until
the procedure is complete. If you wish to interrupt the process,
simply press the DEC button.
6.18 Backup Memory
Backup Memory mode allows you to store permanently the selec-
ted values in the Programmer’s integral memory. Press the INC but-
ton to start the process, and the Programmer then beeps once
every second until the procedure is complete. The values set on the
speed controller itself are not affected by this action.
If you wish to interrupt the process, simply press the DEC button.
We guarantee this speed controller for a period of 24 months. Proof for
the commencement and conclusion of this guarantee period is provi-
ded by your receipt from the model shop, which you obtained when
you purchased the product. Any repairs carried out under guarantee
do not extend the original guarantee period. During this period we will
correct any operating faults, production defects and material faults
which arise, at no charge to you. We will not entertain any claims bey-
ond these terms, e.g. consequent damage.
The unit must be returned to us carriage-paid; it will also be returned to
you carriage-paid. We will not accept goods sent to us without pre-
paid carriage. We accept no liability for transit damage and the loss of
your shipment; we therefore recommend that you take out suitable
insurance to cover these risks. Send the unit to the Service Centre
responsible for your country. The following conditions must be fulfilled
if we are to process your guarantee claim:
• Send proof of purchase (till receipt) with your shipment.
• The unit must have been operated in accordance with the operating
instructions.
• The unit must have been operated with the recommended power
sources and genuine robbe accessories.
• The unit must not exhibit damage due to damp, unauthorised inter-
vention, excessive voltage, overload conditions or mechanical
damage.
• Please include a concise, accurate description of the fault or defect.
- Keep within the values stated in the speed controller’s Specification.
- Take care to observe correct polarity in all connecting cables.
- It is essential to avoid short-circuits.
- Install or pack the speed controller in such a way that it cannot come
into contact with grease, oil or water.
- Ensure adequate air circulation round the speed controller.
- Keep well clear of the rotational plane of the propeller when the bat-
tery is connected to the motor - injury hazard.
We reserve the right to introduce technical modifications.
7. GUARANTEE
8. SAFETY NOTES
6.13 Motor Pole Number
In Motor Pole Number mode you can enter the number of poles in
your motor. This value is important for indicating the exact rotatio-
nal speed. The available range extends from 2 to 36 poles.
6.14 Gear Ratio
This mode allows you to enter the individual gearbox ratio you are
using. The value for rotational speed indication is calculated using
the number of motor poles and the gearbox reduction ratio. The
available range of values is from 1.0 : 1 to 25.0 : 1.
9. CONFORMITY DECLARATION
robbe Modellsport GmbH & Co. KG hereby declares that this pro-
duct satisfies the fundamental requirements and other relevant regu-
lations contained in the following Directives:
• Law regarding radio system and telecommunications apparatus
(FTEG) and Directive 1999/5/EG (R&TTE)
• Directive RL 2004/108/EG (Electro-magnetic compatibility)
• Directive LVD 72-23 / 93/68 EWG (Low Voltage Directive)
The original Conformity Declaration can be viewed on the Internet
under www.robbe.com: click on the logo button marked “Conform”
which is included in each device description.
