Operating Instructions
Roxxy BL-Control 900 series
9
3. Programming the stick positions
1. Connect the speed controller as shown in the wiring diagram
(but don’t connect the drive battery).
2. Switch the transmitter on, and move the throttle stick to the
“forward” position.
3. Connect the drive battery to the speed controller.
4. The controller emits a brief series of beeps to confirm con-
nection.
5. After about ten seconds a double series of beeps confirms that it
has detected the “stick forward” position.
6. Move the throttle stick to the “stop” position. A brief series of
beeps confirms that the controller has detected the “stop” posi-
tion.
7. Move the throttle stick to the “reverse” position; a triple series of
beeps confirms that the controller has detected the “reverse”
position.
Note:
If the LED lights up after point 3.1.2, you must reverse the throttle
channel using the transmitter’s SERVO REVERSE facility. Discon-
nect the drive battery from the speed controller, then start again at
point 3.1.1. The “forward” position of the throttle stick most be at or
close to its mechanical end-stop.
3.2 Programming the stick positions “forward” and
“stop”
The throttle stick positions “forward” and “stop” for “forward only”
controllers are programmed in the same manner as far as point
3.1.6. The procedure is confirmed with a triple series of beeps.
4.1 Programming the speed controller parameters wit-
hout using the Programmer
There are five programmable parameters.
This is the procedure for
entering
programming mode:
1. Connect the speed controller as shown in the wiring diagram (but
don’t connect the drive battery).
2. Switch the transmitter on, and move the throttle stick to the
“forward” position.
3. Connect the drive battery to the speed controller.
4. The controller emits a brief series of beeps to confirm connection.
5. After about ten seconds you will hear a double series of beeps, fol-
lowed by a triple series of beeps after a further three seconds.
The speed controller
now
emits a continuous series of single beeps
and LED flashes to confirm that Parameter 1 has been selected.
The parameter to be programmed is
selected
using the following
sequence of throttle stick positions: move the throttle stick briefly
from the “forward” position to the “stop” position then back to the
“forward” position again. The controller
now
emits continuous dou-
ble beeps and LED flashes to confirm that Parameter 2 has been
selected. Repeat the sequence of throttle stick movements descri-
bed above in order to select Parameters 3, 4 and 5.
To
change
the parameter you must first move the throttle stick from
the “forward” position to the “stop” position, and leave the throttle
stick in the “stop” position for at least three seconds.
The
actual
parameter is
altered
by moving the throttle stick rapidly
from the “stop” position to the “forward” position and back.
BEC:
integral receiver power supply.
POR:
power-on guard, prevents the motor starting accidentally.
PCO:
low voltage cut-off. The speed controller switches the motor off
in good time when the battery is nearly discharged, in order to reserve
sufficient battery capacity for controlling the model, and in order to
avoid deep-discharging the drive battery (optionally for NC / NiMH or
LiPo battery).
hec:
high pulse frequency for fine control of motor speed; also avoids
premature magnet degradation.
SPS:
Super Programming System
Cool Power FET:
New generation of transistors
WP:
Splashproof construction (Water Protect)
Opto:
Galvanic separation between motor interference and receiver
RX-Filter:
Switches the speed controller off if the transmitter signal is
absent or invalid.
TOP:
Double overload protection (Thermal Overload Protection)
TP:
Thermal fuse (Thermal Protection)
3.1 Programming the stick positions “forward”, “stop”
and “reverse”
The change is
stored
by moving the throttle stick from the “stop” po-
sition to the “forward” position.
The final step is to disconnect the drive battery; this concludes the
process and adopts the programmed settings.
The speed controller is now programmed, and is ready for use.
Parameter type
Beep
LED
Parameter 1
Battery type
1 x
1 x
Parameter 2
Direction of motor rotation
2 x
2 x
Parameter 3
- Brake ON / OFF (AIR)
- Brake ON / OFF (HELI)
3 x
3 x
Parameter 4
Model type AIR / HELI
4 x
4 x
Parameter 5
Model type BOAT / CAR
5 x
5 x
Parameter type
LED ON
Beep every 2 Sec.
LED flashes
Beep every 0,5 Sec.
Battery type
LiPo
NiCD/NiMH
Direction of rotation
Normal
Reverse
Brake (AIR)
Governor (HELI)
Reverse (CAR, BOAT)
OFF
OFF
OFF
ON
ON
ON
Model type
(AIR / HELI)
AIR
HELI
Model type
(BOAT / CAR)
BOAT
CAR
4.2 Characteristics, protective functions
4. Programming the speed controller parameters
Caution:
If you wish to change the model type (Parameter 4 or Parameter
5), please note that this parameter must be set before you
change the other parameters.
