www.
robbe
.com
6
E N G L I S H
USER MANUAL
RO-CONTROL PRO WIFI ESC
M o d e l l s p o r t
RO-CONTROL PRO WIFI 2-6S 80 A HV-BEC Nr.: 8730
RO-CONTROL PRO WIFI 2-6S 100 A HV-BEC Nr.: 8731
RO-CONTROL PRO WIFI 2-6S 130 A HV-BEC Nr.: 8732
• Use of a powerful microprocessor, unique circuit variants, very good interference suppression
• Can be used for motors with a maximum speed of up to 210,000 rpm.
• adjustable start mode, fast throttle response, uniform linear control, can be used for wing and heli-
copter models
• Comprehensive protective functions ensure a high level of safety for the controllers.
• For safety reasons, the motor does not start immediately when switched on, even if the throttle is not in
the motor stop position.
• The operating status can be indicated by an audible alarm.
•
ASCF (Active Switch Continued Flow) technology (higher efficiency) massively reduces heat generati
-
on
• WiFi supported programming via ROBBE Smartphone APP (additional RO-CONTROL PRO WIFI MODUL
required).
•
Supports online flight data acquisition and real-time recording at close range via the Smartphone App
(additional RO-CONTROL PRO WIFI MODUL required). Download on www.robbe.com/downloads .
•
Reversal of direction of rotation possible during the flight, this causes a strong delay of the model.
• Aluminium housing for effective heat dissipation and slow temperature rise
01. MAIN FEATURES
04. OPERATION MANUAL
02. SPECIFICATIONS
03. CONNECTION DIAGRAM
1. NORMAL SWITCH-ON PROCEDURE
Direction of rotation signal line: Connect it to a two-stage receiver switching channel to re-
verse motor rotation during flight.
Throttle signal line: Connect it to the receiver‘s throttle channel. The white wire is used to trans-
mit the signal.
ESC
Cont.
cur-
rent
Burst
current
BEC
Cells
Weight
Dimensions
RO-CONTROL PRO WIFI 80A
80 A
100 A
8,4V/7,4V
6V/5V, 10A
2 – 6S
125 g
82,5x39,5x23,5 mm
RO-CONTROL PRO WIFI 100A 100 A
120 A
8,4V/7,4V
6V/5V, 10A
2 – 6S
127 g
82,5x39,5x23,5 mm
RO-CONTROL PRO WIFI 130A 130 A
150 A
8,4V/7,4V
6V/5V, 10A
2 – 6S
132 g
82,5x39,5x23,5 mm
Thank you very much for choosing an electric flight controller from our range. Any
improper use may result in personal injury or damage to the product and model com-
ponents. This high performance controller for RC models can be dangerous. We strongly
recommend that you read this manual carefully and completely. We are not responsible
for any loss caused by unauthorized modifications to our product. We reserve the right to
change the circuit, design, specifications and requirements for use of the product without
prior notice.
Please make sure that all solder joints are insulated with shrink tubing
The picture shows a reference controller.
Switch on the transmitter,
bring the throttle stick into
the lowest position.
Connect the ESC to the battery, wait 2
sec., the motor emits some short „BEEP“
(♪) signals, to display the number of
LiPo cells.
The ESC is ready to run
Wait 1 second, 1 long and 1 short tone
(♫, ♪) mean „no brake“.
A long tone (♫) means „brake availa
-
ble“. The ESC is now ready for use.
WiFi module connection line: Connection cable to the RO-CONTROL PRO WiFi module. This
supports programming and the recognition of real-time data via the ROBBE smartphone APP.