www.
robbe
.com
E N G L I S H
7
M o d e l l s p o r t
USER MANUAL
RO-CONTROL PRO WIFI ESC
RO-CONTROL PRO WIFI 2-6S 80 A HV-BEC Nr.: 8730
RO-CONTROL PRO WIFI 2-6S 100 A HV-BEC Nr.: 8731
RO-CONTROL PRO WIFI 2-6S 130 A HV-BEC Nr.: 8732
2. THROTTLE STICK CALIBRATION
Turn on the transmitter
and bring the throttle stick
into the upper position
Connect the ESC to the battery, wait
2 seconds, if the motor emits two short
„BEEP BEEP“ signals (♪, ♪), the full
throttle position is stored.
Wait 1 second, 1 long and 1 short tone
(♫, ♪) mean „no brake“.
A long tone (♫) means „brake availa
-
ble“. The ESC is now ready for use.
Bring the throttle stick
within 3 sec. into the
lower position. After 1 sec.
is the motor off position
is saved. The motor gives
short „BEEP“ (♪, ♪) signals, so that the
number of LiPo cells is displayed.
3. PROGRAMMING
Switch on
the transmitter,
bring the
throttle stick
the upper position
Connect the ESC to the
battery, wait 2 seconds until
the motor emits two short
„BEEP BEEP“ signals (♪, ♪).
Then wait 5 seconds until
the motor emits a special
tone sequence indicating
that the controller is in pro-
gramming mode.
It is recommended to use the ROBBE app in conjunction with the RO-CONTROL PRO WIFI module to
change the parameters, as this is much easier and you have a visual control of the settings. The pro-
gramming via the transmitter is described below:
Select parameter
After activating the programming mode, you will hear tones that sound
in a loop one after the other. The signals are each assigned to a speci-
fic parameter.
When the
motor emits
the „end“
tone, move
the throttle
to the zero
position.
After 3
seconds the
motor emits
a special
tone. This will
activate the
exit from the
program-
ming mode.
Parameter
Tone sequences
1
Brake
1 short
♪
2
Battery type
2 short
♪, ♪
3
Cut-Off voltage
3 short
♪, ♪, ♪
4
Timing
4 short
♪, ♪, ♪, ♪
5
Start mode
1 long
♫
6
Governor mode
1 long / 1 short
♫, ♪
7
PWM frequency
1 long / 2 short
♫, ♪, ♪
8
BEC output voltage
1 long / 3 short
♫, ♪, ♪, ♪
9
Cut-Off mode
1 long / 4 short
♫, ♪, ♪, ♪, ♪
10
Battery cells
2 long
♫, ♫,
11
Rotation direction
2 long / 1 short
♫, ♫, ♪
12
ASCF
2 long / 2 short
♫, ♫, ♪, ♪
13
Reverse function
2 long / 3 short
♫, ♫, ♪, ♪, ♪
14
Factory reset
2 long / 4 short
♫, ♫, ♪, ♪, ♪, ♪
15
End
3 long
♫, ♫, ♫
Note: 1 long tone „Beeeep-“ (♫) corresponds to 5 short beeps
„Beep-“ (♪), e.g. 1 long tone „Beeeep-“ (♫) and 1 short beep (♪)
corresponds to parameter 6.
Set
parameter
After the motor has emitted
a tone sequence parameter,
move the throttle stick to the
lower position to activate this
parameter. Then the possible
values of the parameter are
displayed in a loop as tones
(see table below).
Move the throttle stick to the top
position after the tone corresponding
to the desired value of the parameter
has been emitted by the motor. After
that, the motor emits a special sound
and the value of the parameter is
preset and stored.
Just wait if you want to configure other
parameters. It returns to
the 1st parameter. The
operation method is the
same.
